The Grumman F9F Panther had the distinction of winning the US Navys first victory in the skys over Korea when it downed a Yak 9 in an air to air engagement. Developed at the end of WW2, with the maiden flight taking place in November 1947, this great looking aircraft was not in front line service for long before being replaced by newer swept wing designs, and ended its career largely in reserve squadrons. Despite this short career in aviation terms, the Panther has many fans.
This very scale looking EPO model very much does the Panther justice, and looks amazing in the sky with those huge colourful wing tanks. The very powerful alloy EDF unit supplies lots of thrust and sounds fantastic, performance is superb even on 3s with plenty of vertical. Being the hand-launch version gives you options for retracts if you so wish as the mounting plates are pre-fitted. All the high torque servos are pre-fitted, as is the fully programmable ESC and UBEC which gives the option of 4.8v or 6v output to the RX.
This is a quality scale model that is a little more involved than your average Plug N Fly in terms of build, but the reward for the RC pilot is one of the best flying & looking foam models in the 70mm class.
Flying Weight: 1000~1100g
EDF: Alloy 68mm with 2848 Brushless inrunner 4370kv (Static Thrust on 3s - 1150g~1200g)
ESC: 60A OPTO
Servo: 4 x 9g High Torque
Comprehensive Decal Sheet
Your Own 4 Channel TX/RX
3700mAh 3s ~ 5000mAh 3s Lipoly Battery
Hmotnost ( g )
Came very well wraped, go's together fast for a kit, foam is first class but had a couple of blisters in the paint, used epoxy to glue it but be warned sand the paint before glueing, decals are nice and are on three sheets good manual with C of G. The wing is glued on so if you wont to fit retracks do it before fixing the wing though ply plates are pre fitted and servoless retracks would be easy to fit at any time. waiting for weather to maiden her it really likes the part.
I hope she flys as good as she looksIts a realy nice model. I changed the engine and esc with a rclander 68mm, 1.7 kg thrust and 80 amp esc. I modified it with flaps and dsr b retracts. Had to do some cutting to make it fit but it was worth it. I also put on the turnigy rc led lightning system. I use a 4 cell 4500 mah battery and a separate receiver battery. (2 cell 850 mah. life battery, 48 gram). Tot weight is 1.750 kg and flying time with different power setting is 12min.Not a bad foamy EDF, it has a nice shiny painted finish with minimal moulding dots and lines, it can be seen that these have been avoided where possible and it looks neat. Its not smooth smooth, but its not bad for a painted foam finish.
Instructions are OK, limited though, and show assembly steps which on my model have already been completed. This did not save time at all as the assembly was pretty shoddy, parts did not fit, control surfaces were not aligned and there was a significant amount of excess glue in the hinges preventing movement. After a couple hours trimming with the dremel, I have managed to get it to work. Also note that the "perfect fit" DSRB retracts are no where near a perfect fit, and require cutting and gluing in blocks for the retracts.
I will be running 2x 3S 2150 batteries which need to be jammed all the way in the nose (past the battery tray) to get it to balance. EDF does run smooth on mine though, and will produce around 0.8-0.9:1 thrust with the retracts, and top 1-1.1:1 without the retracts.
Overall, a great looking model, great finish on the foam with sharp trailing edges on the wing (looks great). Might paint the surfaces a bit to help distinguish top and bottom.
Would I buy it again? so far I'm pretty impressed by the foam model, but let down by the poor assembly. With some work that I'm prepared to put in, at this price point, I think IThe model is ok but the retracts that are supposed to be an exact fit do no fit without triming wood at mounts and also nos has to modified to accept nose wheel electric retract. this was the TGY-DSRB retracts.
As for weight and balance try putting fiberglass in the nose to strengthen it and the balance will be fine. This has to be done before glueing it on. Tha plane is slower with the electric retracts and a better motor would be good.
CharlesFinally got it balanced. After a burnt out motor and splitting it in half twice. The alloy EDF needs a 4000mah batt up front to get the CG forward enough. Flys steady and has huge presence in the air. Sounds a million bucks and fan is smooooooth. Not really for beginners and even then I'd only take it out for special occasions. Enjoy.