Registrovat

Product Finder

Nastavení

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Registrovat
Shipped From:
  • USA

FPV 433Mhz Radio Telemetry Kit 100mW V1.1

FPV 433Mhz Radio Telemetry Kit 100mW V1.1

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Váha:
47 g
SKU:
9387000030-0

Combine

essential items and
acc
Popis
produktu

This Telemetry radio set allows you to link to a flight controller such as our HK Pilot Mega 2.5 or Multiwii AIO via a USB equipped device such as a computer, laptop or tablet supporting a USB connection (OTG). The Radio set not only lets you see live data such as live GPS position overlaid on a map (if the flight controller has the GPS option) to system voltage, heading, waypoint navagation even artificial horizon and so much more, using open source MAVlink based ground station software. You can even fly your aircraft with a joystick via your computer and update settings live! Or just use it for your DIY projects that needs a wireless Serial interface. This kit offers a great low price, longer range (approx one mile with supplied antennas) and superior performance. The system utilizes the 433Mhz band and provides a full-duplex link using HopeRF's HM-TRP modules running custom, open source, firmware.

The SiK firmware includes a bootloader that permits radio firmware upgrades over the serial interface, and configuration of system parameters. Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through the 3DR Radio configurator and AT commands.

Interface to the module is via standard 5V-tolerant TTL serial / FT232 USB serial.

Features:
• Very small size
• Light weight (under 4 grams without antenna)
• 433Mhz frequency band
• Receiver sensitivity to -117 dBm
• Transmit power up to 20dBm (100mW)
• Transparent serial link
• Air data rates up to 250kbps
• Range of approx 1 mile with supplied antennas
• Demonstrated range of several kilometers with a small omni antenna
• Can be used with a bi-directional amplifier for even more range
• MAVLink protocol framing and status reporting
• Frequency hopping spread spectrum (FHSS)
• Adaptive time division multiplexing (TDM)
• Support for LBT and AFA
• Configurable duty cycle
• Built in error correcting code (can correct up to 25% data bit errors)
• Open source firmware
• AT commands for radio configuration
• RT commands for remote radio configuration
• Adaptive flow control when used with APM
• Based on the HopeRF HM-TRP radio module, featuring an SiLabs Si1000 RF microcontroller.
• Upgraded to more convince Molex 1.25mm


Specs:
Band: 433MHz
Antenna connectors: RP-SMA connector
Output power: 100mW (20dBm), adjustable between 1-20dBm
Sensitivity: -117dBm sensitivity
Interface: Standard TTL UART
Connection status: LED indicators


Includes:
Radio Telemetry base station (USB Connection)
Telemetry Transceiver (Pin Header)
lead set x1
Antenna x 2

This product is based on the 3DRadio Project from 3D Robotics.

Product
Specifications

Další informace

  • SKU:
    9387000030-0
  • Brand:
    nedefinováno
  • Hmotnost ( g )
    47.00
  • Délka
    100.00
  • Width:
    20.00
  • Výška:
    40.00
Community
Discussions
Rate&
Review

Napište vlastní recenzi

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
This is a review of the "HK 433MHz Radio Telemetry Kit 100mW V1.1" that I received a couple of weeks ago. The shipment arrived quickly, well packed from the International Warehouse, well done Hobby King! Another nicely done order.

The product looked good, well done PC boards, great looking parts and assembly, and I had ordered the optional cases as well. They looked great also, fit well, and snapped on very snugly - I had to use a use a tool to snap them shut, great fit.

I found a video on You Tube that showed an Australian gent successfully pairing them up, and I followed it and had the same success. My Netbook with Mission Planner software and Quadcopter with HKPilot Mega 2.7 were talking up a storm!

It seemed prudent to check the antennas, having read much pro & con about them. It turns out they were were tuned somewhat low. I used my MFJ 269 for starters, and they were too low to read. The 269 only covers 420 to 470MHz, and they were below that range.

I borrowed a VIA ECHO 1000SF antenna analyzer from a company that I consult for, and the antennas were both resonant at about 380MHz, give or take. At 433MHz, one antenna had an SWR of 9.5:1, and the other was 7.5:1. Time to Tweak!

Using C-clip pliers, I spread the bottom of the "ducky" and lifted it off of the tilt base. That exposed the piece of coax soldered to the spring that is the antenna. That is what is in
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Be carefull if you are looking for long range. This item works well but at a maximum of 250 meters with supplied antennas. During gound distance test, the signal drops to zero after 100meters. Perhaps the antennas are not 433 Mhz (they are marked 2.4 Ghz but in discussions somebody says they are not 2.4 but 433, i have a doubt.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Fantastic item, I use it all the time in all places and electronics. Nice n shiny finish, good covering
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I'm using these. And they are working fine. Range could be better though. I still need to verify the range of one mile. So far I lost connection before 100meters.
Antenna connectors could be stronger, I accidentally broke the antenna connector of the ground module during transport. (remove the antennas during transport)
Today I would choose the new version because then its easier to update the firmware.

verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Works very well with APM2.5. Just plug and fly. Only minus is that updating the firmware on remote unit could be easier if you could plug the FTDI connector directly to the board.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This kit is awesome, i have been using it for some time now. Its stable, its plug and play even in a MAC.

I will take away a star on antenna quality, both of my antennas sounds like something is loose inside. it does work, but a bad thing is a bad thing.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Arrived quickly , but as with so many of these 3dr clones , they came supplied with 2.4Ghz antennas and not the 433Mhz ones ,

I now have to source 433Mhz ones for this kit .

overall a good price despite the shortcomings.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
These work very well for me. just plug and play. i have used them with my APM 2.5. works well with my samsung galaxy s3.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
?? ???????? ????????? 2.4??? ?? ?????? ????? ????????
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very useful Telemetry Kit. I use it with my HK AIO Board (MegaPirateNG). Pefect connection between Smartphone with DroidPlanner 2 and QuadCoptet. Quality is also good. Must buy!
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload video
Upload
Files

Combine

essential items and
acc

Štítky produktu

Štítky oddělujte mezerou. Víceslovné uzavřete v apostrofech (').