New Items Fórum
Registrovat

Total Price

0,00 €

Cart 0 Cart 0 Loading...

HK Pilot Power VI Module, Distribution Board And Dual UBEC ALL-In-One (120A and 10s)

HK Pilot Power VI Module, Distribution Board And Dual UBEC ALL-In-One (120A and 10s)

Now save Uložit 0,00 € 0,00 €

32,70 €
Stav:
Není skladem!
Váha:
101 g
SKU:
9387000061-0
WANT FREE SHIPPING? Click here to find out more!

The HK Pilot Power distribution and power module in one is simplifying your setup, reducing points of failures and makes for a clean and tidy install. The ALL-in-One has a PDB, Dual 12V and 5.3V UBECs, Voltage and Amperage sensors all integrated on a standardized 45mm mounting package.

The power distribution side is on a standardized 45x45mm mounting size and is rated at 120A of current and more than enough contact points for a Octocopter. The dual Ubec’s are 12V and 5.3V respectively, for the HK pilot Flight controller and 12V aux gear such as FPV. The Amp and voltage sensor are compatible with HK pilot FC and APM/Pixhawk FC with the standardized 6 pin connector. The ALL-IN-ONE is 10s capable as well for HV application or right at home with 3s setups too.

Features:
PDB/12V and 5.3V UBECs/V and A Sensors all in one
120A capable
10s capable
16 power contact outputs 8+ 8-
Standardized sizing
HK Pilot APM/Pixhawk compatible

Specs:
PCB Current: 120A outputs (MAX)
UBEC output current :2.5A
Power input: 2 x contact points
Power output: 16/8 x contact points and 2 for 12V UBEC 5.3V on the 6 Pin Plug
Dimensions: 50x50x5mm, Mounting 45x45
Weight: 11.6g 

Package Includes
UBEC power distribution board *1
6pin cable *1

  • SKU 9387000061-0
  • Brand H-King
  • Kapacita ( mAh ) -
  • Hmotnost ( g ) 101.00
  • Délka 50.00
  • Width 10.00
  • Výška 50.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Nice little PDB with everything you need

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Nice little PDB with everything you need

This board could benefit from a few design changes. First, the board should have thermal relief pads to make soldering easier. Second, holes could be drilled to make the physical wire connection more robust. Third, the addition of LEDs on the voltage regulators would make this product a little more user friendly.

I agree with the other reviewers that soldering to this board is very difficult. The secret is to use a good quality gun with good thermal recovery.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This board could benefit from a few design changes. First, the board should have thermal relief pads to make soldering easier. Second, holes could be drilled to make the physical wire connection more robust. Third, the addition of LEDs on the voltage regulators would make this product a little more user friendly.

I agree with the other reviewers that soldering to this board is very difficult. The secret is to use a good quality gun with good thermal recovery.

bonne plaque de distribution, pour le poids, le prix, et les deux sorties 5V et 12V

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

bonne plaque de distribution, pour le poids, le prix, et les deux sorties 5V et 12V

these boards are pretty much bulletproof, its my 4th one and i havn't had any issues with any of them

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

these boards are pretty much bulletproof, its my 4th one and i havn't had any issues with any of them

Nicely made and finished power distribution board with many input and output pads which provide easy soldering (just put the soldering iron on 400 degrees). Because of this it will be really hard to notice that you soldered wires by hand.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Nicely made and finished power distribution board with many input and output pads which provide easy soldering (just put the soldering iron on 400 degrees). Because of this it will be really hard to notice that you soldered wires by hand.

???? ??? 120????? ??..

?? ????!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

???? ??? 120????? ??..

?? ????!

Used the PDB on an X580 frame with a 4S battery powering 4 NTM 35-48 motors. Read the reviews of it being hard to solder, a cheap 15W soldering iron with an old tip will certainly not do the trick but a 65W iron worked just fine. Haven't used the BEC capability so can't comment, and since I have a quad only using half of the board but the price can't be beat and saves you from having to fabricate your own. Very pleased.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Used the PDB on an X580 frame with a 4S battery powering 4 NTM 35-48 motors. Read the reviews of it being hard to solder, a cheap 15W soldering iron with an old tip will certainly not do the trick but a 65W iron worked just fine. Haven't used the BEC capability so can't comment, and since I have a quad only using half of the board but the price can't be beat and saves you from having to fabricate your own. Very pleased.

very difficult to weld while you use flux. I do not know what has or varnish coating leads but it is very difficult to weld. a good product that eventually turns into a nightmare thinking that cables can be released. As the wires carry the energy of our birds , we know what happens in case of a power failure ...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

very difficult to weld while you use flux. I do not know what has or varnish coating leads but it is very difficult to weld. a good product that eventually turns into a nightmare thinking that cables can be released. As the wires carry the energy of our birds , we know what happens in case of a power failure ...

I purchased this for a QAV250 clone, the board is a good size but a bit bulky for a mini quad. No problems running it but not ideal for super compact setups. Great value for money.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I purchased this for a QAV250 clone, the board is a good size but a bit bulky for a mini quad. No problems running it but not ideal for super compact setups. Great value for money.

Well.. I thought I found the perfect board.. When you get it you think.. Nice.. Good quality. The board is really thick. Perfect for High CUrrent. 5.3/Amperage Reading/12V - PERFECT.

But there is a bottom side. As some mentioned here: ITs the 12V Regulator. After ~4h of total use it poofed in smoke. Hopefully my 12V Cam Hardware is not damaged. Need to see what Hobbyking does.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Well.. I thought I found the perfect board.. When you get it you think.. Nice.. Good quality. The board is really thick. Perfect for High CUrrent. 5.3/Amperage Reading/12V - PERFECT.

But there is a bottom side. As some mentioned here: ITs the 12V Regulator. After ~4h of total use it poofed in smoke. Hopefully my 12V Cam Hardware is not damaged. Need to see what Hobbyking does.

  1. 1
  2. 2
Customer files
PDB in FPV250 Download [3102]
Board before installation Download [1553]
No File Name Download [2966]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save