New Items Fórum
Registrovat

Total Price

0,00 €

Cart 0 Cart 0 Loading...

HobbyKing AP05 3000kv Brushless Micro Motor (5.4g)

HobbyKing AP05 3000kv Brushless Micro Motor (5.4g)

Shipped From:
  • Global
QTY:

Now save Uložit 0,00 € 0,00 €

15,91 €
Stav:
Skladem
Váha:
21 g
SKU:
HK-AP05-3000
WANT FREE SHIPPING? Click here to find out more!

High quality micro motors. Precision wound with silver-copper wire and ultra hard-press laminations.
Extreme performance and efficiency for your micro plane.

Factory Spec.
Kv: 3000rpm/v
Lipo Range: 1~2S (3.7~7.4V)
Suggested prop: 5030
Max current: 3A
Burst current (5sec): 4A 
Weight: 5.4g (including mount and wire)
Shaft: 1.5mm
Shaft length: 14mm
Dimensions : 14 x 13mm
 
Test data:
5030 prop (Recommended)
Voltage: 7V
Current: 2.8A
Thrust: 110g
 
For 70g 3D airplane and 120g normal flying.

  • SKU HK-AP05-3000
  • Brand HobbyKing
  • Hmotnost ( g ) 21.00
  • Délka 83.00
  • Width 14.00
  • Výška 60.00
  • Kv (rpm / v) 3000.00
  • Maximální proudy (A) 4.00
  • Odpor ( mh) 0.00
  • Maximální napětí ( V) 7.00
  • Výkon ( W ) 0.00
  • Hřídel A ( mm ) 2.00
  • Délka B ( mm ) 12.00
  • Průměr C ( mm ) 13.00
  • Může Délka D ( mm ) 8.00
  • Celková délka E ( mm ) 19.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

??????? ????? ?????????, ? ??????? ????? ??????, ??????? ?? ??????.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

??????? ????? ?????????, ? ??????? ????? ??????, ??????? ?? ??????.

Works great with a handlaunch glider conversion..

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Works great with a handlaunch glider conversion..

Used this engine as a replacement for the original gearbox and engine for a SU26XP from Parkzone. Power is roughly the same or somewhat greater. Used together with the 0,7gr BL controller from Hobbyking. Great!! (included a propsaver - 4mm)

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Used this engine as a replacement for the original gearbox and engine for a SU26XP from Parkzone. Power is roughly the same or somewhat greater. Used together with the 0,7gr BL controller from Hobbyking. Great!! (included a propsaver - 4mm)

My P51 Mustang, Dave Rovelen plans, 46 cm wing span, 70 g AUW. GWS EP-4530 prop. Lipo 2S180 mAh nanotech flew like a rocket with this motor half throttle.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

My P51 Mustang, Dave Rovelen plans, 46 cm wing span, 70 g AUW. GWS EP-4530 prop. Lipo 2S180 mAh nanotech flew like a rocket with this motor half throttle.

I swapped this motor into my UM T-28, and wow this thing is fast! Check out the Ultra Micro T-28 thread on RCgroups if you want to see pictures. I used the Plush 6 amp, MAKE SURE YOU INSTALL A 1 amp diode (like 1N4001) between positive line into the brick or you can fry it. Then swap it to brushless and POW! You've got a much faster bird. Heavier too, so it handles a little more wind. Only draw back is that it doesn't "float" as much as it did before.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I swapped this motor into my UM T-28, and wow this thing is fast! Check out the Ultra Micro T-28 thread on RCgroups if you want to see pictures. I used the Plush 6 amp, MAKE SURE YOU INSTALL A 1 amp diode (like 1N4001) between positive line into the brick or you can fry it. Then swap it to brushless and POW! You've got a much faster bird. Heavier too, so it handles a little more wind. Only draw back is that it doesn't "float" as much as it did before.

I used this for my Ultra micro T-28. converted to 2s brushless setup using this motor, TURNIGY Plush 6A /.8bec/6g Speed Controller, and even a slightly large 300mAh nanotech battery. weight including battery was 65.5g, and this setup allows me to pull straight up. I would say to put the throws down slightly since the plane is at least twice as fast now! here's the thread with the info.

http://www.rcgroups.com/forums/showthread.php?t=1282886&page=563

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I used this for my Ultra micro T-28. converted to 2s brushless setup using this motor, TURNIGY Plush 6A /.8bec/6g Speed Controller, and even a slightly large 300mAh nanotech battery. weight including battery was 65.5g, and this setup allows me to pull straight up. I would say to put the throws down slightly since the plane is at least twice as fast now! here's the thread with the info.

http://www.rcgroups.com/forums/showthread.php?t=1282886&page=563

Very good quality for a very powerful motor.
I use it on a 100 g slowflyer plane and it works well.
I think this motor can trust up to 150 g slowflyer plane

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very good quality for a very powerful motor.
I use it on a 100 g slowflyer plane and it works well.
I think this motor can trust up to 150 g slowflyer plane

finally install it in my home built depron patern 3D plane AUW 70g on 2s 180 mah 4.5X4 prop have a good power and speed, little noisy at full power but all and all very happy with it, will get some more for the next project.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

finally install it in my home built depron patern 3D plane AUW 70g on 2s 180 mah 4.5X4 prop have a good power and speed, little noisy at full power but all and all very happy with it, will get some more for the next project.

HIGHLY RECOMMENDED installed in my 2s converted PZ Sukhoi XP micro, with a 5x43 prop and it HAULS. Faster than a newer UMX Sbach! The only reason for quality 4 stars is because the wires are soooooo tiny and brittle, had to hot glue on the solder points on the ESC to prevent them from breaking with vibrations.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

HIGHLY RECOMMENDED installed in my 2s converted PZ Sukhoi XP micro, with a 5x43 prop and it HAULS. Faster than a newer UMX Sbach! The only reason for quality 4 stars is because the wires are soooooo tiny and brittle, had to hot glue on the solder points on the ESC to prevent them from breaking with vibrations.

Outstanding little motor, combined this with a 5A 1S Brushless Controller, GWS 5x3 prop on a 75g depron wing and it's very fast

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Outstanding little motor, combined this with a 5A 1S Brushless Controller, GWS 5x3 prop on a 75g depron wing and it's very fast

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!