The next evolution of the rotor revolution is here!! The KK-mini is packing all the same power, but with a new mighty-mini form factor.
The KK-Mini is the next Big/Small evolution of the first generation KK flight control boards. The KK-Mini is based on the KK2.1.5 architecture and has all the same inputs and outputs as well as the full functionality of its big brother. The new 36mm designed was adapted to fit the needs of the new mini market, but don’t let its size fool you as it's just as much at home in any size multi-rotor. The KK mini still utilizes a built in GUI using a hi-res mini LCD and 4 micro buttons for the same great KK experience. It was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts.
A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts!
The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system, making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK-Mini is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for on-board soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board.
The KK-Mini added polarity protection to the voltage sense header and on-board buzzer. The voltage sense line has been updated for better accuracy.
If you’re new to multi-rotor flight or have been unsure about how to setup a KK board, then the KK-Mini was built for you. The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy.
Size: 36x36x11.5mm (mounting holes 30.5x30.5mm)
IC: Atmega644 PA
Gyro/Acc: 6050MPU InvenSense Inc.
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels)
Signal to ESC: 1520us
LCD size: 24*18mm
Mini buttons size:Four 3.3*4.2mm
Voltage sensor: One red positive pin header for.
Input rail: Single row 2.54mm pitch pin header for input signal
Firmware Version: 1.6:
Singlecopter 2M 2S
Singlecopter 1M 4S
(Custom Mix via the "Mixer Editor" option)
The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.
Customer self-update function.
Satellite input use Satellite-to-CPPM converter (#24524) at throttle channel(need steveis SW)
Sbus input use SBUS-to-CPPM converter (#52185) at throttle channell(need steveis SW)
** Note: It is all ways recommended to update to the latest software version as part of your initial setup.(This is different than v1. 6 for KK2.0)
*** Note: The KK-Mini uses the same firmware as the KK2.1~2.1.5 series
Hmotnost ( g )
My 1st one had issues with powering up and with blank screen. Hobby king replaced it with a new one and it was perfect. I flashed Open Aero firmware and used it on my bixler 2 with stabilizer and auto leveling modeGefällt es Dir?
Jeg satt dette styret på en tri-Copter for en stund og deretter på en 330 quad som jeg har fløyet ganske mye. Ved hjelp RC911 firmware, som jeg kan anbefale. Svært stabil, har flere profiler, tre fly moduser og en død-band hvis du trenger det. Bra for flips, loops ruller etc. Vil sannsynligvis kjøpe en annen for 150-180 størrelse quad jeg planlegger. Bruke den med TGY i6 for en virkelig bærbar oppsett. Tenkte på en Naze 32 akro, men jeg ønsker ikke å hassle med å plugge inn i datamaskinen når jeg ønsker å endre en innstilling. Mini-skjermen er liten, men lesbar og det vil gi deg advarsler også (med rc911) så det er bedre enn et vanlig bord i den forbindelse. Tune den i henhold til instruksjonene og du kan ha tillit til denne kontrolleren.these are the best DIY flight control, no PC connection neededAfter plugging her in, a simple task and right away the L.E.D. came up with Safe and Menu. After a few tries I was able to flick around the menu. Just be careful with the screen. Its mount is only double sided tape. I had to add more to make it sit level. All good!su simplesa y precio son indiscutible............................................................................................................................................................................................................................................................................................................good product, perfect fit for a very small weight. it is not livered with all cables for split the commandThis multi rotor boards flys my quad 250 smooth. With the many features of the board I am really amazed what can be accomplished in such a small package.Works amazing right out of the box.used in a 250 quad. right out of the box this thing performed great and after some minor tuning it's lovely.
HK KK-Mini Multi-Rotor FC
Howd to set a board like this up?
Demo of OpenAero2 flashed on a KK-Mini Multi-Rotor Flight Control Board.
RC UFO Flying Saucer
UFO Flying Saucer with Improved Tractor Beam
KK2 SingleCopter 2m 2s Maiden
No File Name download now [202kb] KKflashing1 download now [202kb] KKflashing2 download now [428kb] 6 pin ISP layout download now [164kb] Photo Both sides download now [945kb] KK MINI CPPM WIRING download now [797kb] ATHome 2 - KK-Mini Flight Control Board download now [61kb] ATHome - KK-Mini Flight Control Board download now [52kb] Both sides download now [945kb] 616624324X1532726X53.JPG download now [44kb] Orange receiver connection-1 download now [4.61Mb] Orange receiver connection-2 download now [4.75Mb] current version - bad contrast download now [515.45Kb]