The HK Mi Series servos represent the next break through in high precision servo technology. Using Magnetic Induction, rather than a potentiometer, for an unsurpassed level of accuracy and performance.
A great servo for 550~600 Class helicopters such as the T-Rex 550 and HK600
Specs:Mi : Magnetic Induction, uses a Magnetic Rotary Encoder in place of a traditional potentiometer (invented in 1877). Magnetic Rotary encoders have a longer life and suffer less wear.
Voltage: 4.8v / 6v
Speed: 0.08sec / 60 deg (4.8v) - 0.07sec / 60 deg (6v)
Torque: 9.7kg.cm (4.8v) - 11.8kg.com (6v)
Size: 40mm x 20mm x 39.2mm
Gear Train: Full Titanium Alloy
Spline Count: 25
Hmotnost ( g )
Rychlost ( Sec / 60deg )
Točivý moment ( kg) (min . 0,01 kg )
Unit Weight (g):
A ( mm ):
B ( mm )
C ( mm )
D ( mm ):
E ( mm ):
F ( mm )
Unfortunately this product did not last anywhere near long enough to be considered good value. The performance was incredible, however, it lasted only 2 days. I wouldn't recommend buying this unless it was utilised in a setup that will suffer no impact - the gears cannot take it.This Servo is verry fast for helicopter. I need the Servo for a HK600-GT.It's a very fast servo but very fast to die also !! Mounted on a 1/8 off road car...servo is dead after 1/4 of a run !!!
Very disapointed.Ho comprato questo servo per il mio buggy 1/8 e non ho avuto neanche il piacere di finire una scarica. Il servo sembrava veloce e preciso ma riscaldava anche da fermo. dopo una girata di neanche dieci minuti in pista si completamente fermato e scaldava cos tanto da non poter essere toccato con le mani. In buona sostanza soldi buttati.Meine Meinung zu dem Servo.
sehr schnell und kraftvoll, sehr gute Auflsung mit kleinem Totpunkt, Titan Vollmetallgetriebe, Gehuse gut mit O-Ringen abgedichtet und im Servo keine losen Drhte. Also auch vibrationsfet.
Getriebespiel knnte etwas besser sein, Getriebeachsen der Zwischenrder sind nur in Kunststoff gelagert. Messingbuchsen wren besser.
Fr den Preis ein sehr gutes ServoI currently have 5 of these and 4 more coming and run them in all my offroad cars including my 1/8 ebuggy, which is more then enough servo for steering!!! I would buy more if they came in a low profile as well for my touring car!! Wink Wink Hobbyking..... :) Great product!!!Got mine now about 20 Lipo`s in my SC 10 4x4 as a steering servo and I`m very satisfied with it. Very fast, strong enough, good centering, temperature ok, but a bit to much play in the gears. It withstand a couple of hard crashes till now. Next time i will buy the slower one with a little more power, this one ist just to fast (even by driving it with 5,0 Volts).Very disappointed with these. Bought three for my heli cyclic control, thought I would give them a try as up to now I have been impressed with HK products BUT if you intend to use these with Futaba or Align Aluminium Servo horns they only fit on about 50pcnt of the servos! I had two replacements sent but one of these was also wrong. There is clearly a serious quality issue. HK tell me they are only intended to be used with the supplied horns which are plastic, very flexible, and in my opinion will never withstand nearly 12kg of force. In my opinion avoid these unless using for basic low torque applications
i use it for my 1/8 off road car,, it was grate and i will order it again
i use it for my 1/8 off road car,, it was grate and i will order it againI have bought this servo to fit Align Part No HSP61008T D6CJ Metal Servo Horn (RED) Designed for JR servo. The horn will not fit the shaft geometry of the servo gear (either one or the other are out of specs/tolerances). Will not recommend such servo for Align JR Arms/horns alloy components.