The KINGKONG team have done it again. Using their popular 260 FPV frame they have added a great package of gear to make an excellent Plug and Play package complete with FPV camera and Video TX.
This multirotor is powered by the KINGKONG Force 200 Multirotor driving equipment set. The kit has everything you need from a pre tuned mini CC3D flight controller to down to the Spironet Antenna.
The motors are KINGKONG 2204-2300KV (CW and CCW) powered by KINGKONG 12A OPTO BLHeli ESC’s. With a UBEC (5v 3A) power to the PDB. 6040 Propellers will quicken your pace.
There is a preinstalled FPV camera and video TX so just tune in the channel and get flying. The FPV camera is angled so you see where you are going when the race is on.
Just to ensure that your competitors know where you are there is super bright LED strip at the rear as this will be the only part they will see.
This exciting packing not only looks the part but will give you hours of racing enjoyment at the right price.
• Fully molded unibody glass fiber reinforced chassis
• KINGKONG 2204-2300KV Motors (CW and CCW)
• KINGKONG 12A 2-4S OPTO BLHeli ESC’s
• KINGKONG 5V-3A UBEC
• Power and Video distribution board with XT60
• Mini CC3D Flight Controller
• 5040 Propellers (CW and CCW)
• FPV Camera 1000TVL CMOS
• 200mW 5.8GHz Audio/Video Transmitter
• 5.8GHz Circular Polarized Spironet Antenna
• Action camera mount
• Super bright LED module (Make sure your competition knows it's you over taking them!)
Weight: 138g (bare frame)
Voltage: 7.4-14.8V (2-4S LiPoly)
Max Thrust: 440g
Number of Poles: 12N/14P
Prop shaft: 5mm
Motor Shaft: 3mm
Bolt hole spacing: 16mm or 19mm M3
Input Voltage: 7.4-14.8V (2-4S LiPoly)
Constant: 12 Amps
Burst: 20 Amps (5sec max.)
BEC: No BEC, OPTO only
Weight: 7.5g (with wires)
Input Voltage: 6V~28V/DC (2-4S LiPoly)
Output Voltage: 5V
Ripple: Constant: 3 Amps
Input Voltage: 5 ~ 12V DC
View Angle: 120deg
Video TX Specs:
Modulate: Wideband FM Modulate
Video Format: NTSC/PAL
Output Impedance: 50 Ohm
Output Power: 23~24dBm
Operating Voltage: 7V~24V
Supply Current: 190mA
Operating Temperature: -10~85
Video Band Width : 0~8.0 MHz
Audio Carrier Frequency: 6.5MHz
Video Input Level: 0.8~1.2 Vp-p
Video Input Impedance: 75 Ohm
Audio Input Level: 0.5~2.0 Vp-p
Audio Input Impedance: 10K Ohm
Dimension: 40 x 23 x 8mm
Weight: 10g (without antenna)
Band A: 5865, 5845, 5825, 5805, 5785, 5765, 5745, 5725
Band B: 5733, 5752, 5771, 5790, 5809, 5828, 5847, 5866
Band E: 5705, 5685, 5665, 5645, 5885, 5905, 5925, 5945
Band F: 5740, 5760, 5780, 5800, 5820, 5840, 5860, 5880
1 x KINGKONG 260
20 x 6040 Pros (10CW + 10CCW)
1 x Spironet Antenna
1 x ESC PC software communication adapter
1 x Action Cam dampened mount
1 x Cable pack
1 x Cable tie pack
1 x Antenna mount set
1 x USB Cable
5-6 Channel RX/TX
1300-2200mah 11.1V ;1000-1800mah 14.8V
Hmotnost ( g )
Great little quad for a beginner multirotor pilot. This was my first quadcopter and it defenitely facilitated a great introduction to multirotor flight as well as some great fun once I became more confident.
My only major criticism is the frame. It's quite brittle and once an arm is gone it is a pain to re-attach. I will shortly be migrating this hardware to a new body.i bought 2 of these and i cant get enough of it it flies greatShe came just few days ago, cc3d controller is really easy to setup , I checked if the ESCs were all linked as they should and I went for a fly ... I like the feeling she gives, I like the sound of her engine ... I like the green lime LEDs on the back , she can be really faster , all I need now is learn how became good for her , using the right power while turning ... it'll take his time , but since she made me confident with the whole space around me , I'll be keen to do it. I'm feeling in loveAwesome kit for racing.
precio y calidad deseableupon receiving this item everything was looking great. I downloaded the CC3D ground station program on my laptop. The setup wizard has easy to follow directions and once done I set my default parameters and how I wanted to arm it and BAM the thing flies like a dream! I've flown it with a bunch of different batteries, below will be the battery type and how well it did. BTW the winds were really heavy and choppy today so it was fighting a hefty wind. and still performed great enough to pull off a lazy back flip.
FYI there is no low voltage warning the speed controllers will just execute the low voltage cut off.. I highly recommend timing your flight times with low altitude maneuvers until you know how long each battery lasts so you will avoid a crash!
3s 2200mah 40c- lots of power- battery was warm but not hot- 11min flight time
3s 2200mah 25c- decent power- battery was hott after flight- 6 min flight time
3s 1000mah 30c- decent power- battery was warm but not hot- 5min flight time
2s 5000mah 25c- gutless! full throttle it barely climbed (this battery was from my stadium truck)
so in reflection stay with a 3s lipo with at least a 30c rating. I cant wait to try a 4s lipo in this quick and nimble thing! ive been told these 250 class quads like between a 1300mah and 1600 mah battery with a high "c" rating