The Mini Talon FPV V-tail Drone is the new little brother of the popular Talon FPV plane. The all EPO moulded airframe breaks down, and due to its smaller size is great for packing with you on your favorite FPV safari. The kit comes un-assembled with EPO and laser cut plywood parts.
With a 4S 14.8V 10,000mAh LiPoly battery, flight times are long, and wing loading still low thanks to the generous wing area of the Talon. A generous fuselage compartment with large top hatch allows you to access your FPV equipment and flight battery in any configuration you choose. It is an open canvas for your FPV needs.
• Kit - All assembly and equipment installation required
• Moulded EPO airframe
• Laser cut plywood motor mount and wing saddle frame
• Monowheel landing gear protects bottom of fuselage
• Large fuselage compartment accomodates many battery and FPV equipement configurations.
• Two Piece plug in wings with carbon wing tube
Flying Weight: 1000~2000g
Wing Area: 30 sq. dm.
4+ Channel Transmitter and Receiver w/ V-tail mixing
4S 14.8V 5000-10000mAh LiPoly Battery
4 x 9g Servos
2814 1000KV Brushless Motor
40A Brushless Speed Control
Hmotnost ( g )
Super avion pour du fpv cool. Avec un apm dessus et une 4s 5000. Le centrage indiqu est parfait. Le lanc et trs facile mais il faut faire attention au couple de l'hlice lors de la mise des gaz. Prvoir un renfort de la pice en bois qui touche l'atterrissage.
Mont avec un plush 40a, moteur 2217 800kv et helice apc sf 10x4.7 a suffit largement.Not a bad aircraft. Quality is pretty good and it is tough too! Loads of room inside but inconvenient access/battery placement. Need a better system to close top access door and keep it latched. I didn't use v-tail trim and it flew well as a yank and bank. Rear skid section should be redesigned as wooden skid is a weak point. Very fast with the right motor/prop/battery combination. Watch out for roll to the left when launching.I can't be happier with this plane.
It was easy to build, all pieces fit perfectly and are really well finished.
One nice detail is that wings can be easily detached and reliably attached using a screw that holds them in their position.
Having watched some videos, I was concerned about landing speed, but actually it does not need much space to land (watch the video).
It is very stable, and with the motor I used (dys 2217 1500kv) taking off is really easy, and it climbs really well.
The only problem I have found so far is the tail wood landing squid is too fragile, and needs reinforcing.
Here is my maiden flight video (gear list in video details):
https://www.youtube.com/watch?v=exoCKpwOr_0Excellent quality. Used hot glue and epoxy to put it together. Mines 1000g with gopro 3 and without battery so auw will be around 1300g. Hxt900 servos fit as good as perfectly into the slots (they could be .5mm thinner) but its not a big deal. Get some servo extension leads 2x10cm and 2x 20cm would be greatI have to say, I suck it up with the high price of shipping on this FPV Plane, I will tell you right now, it was worth it,, very nice indeed, and lots of room for my gear.. very nice job indeed Hobby King, Thank you..I have Purchase This Plane with Spec Below. Got 30min Flight Time.
-ntm 2826 1000kv
-3 blade 8inch proppeller
-600mw Boscam 32ch VTX.
I use vector OSD FC ,60HK esc SimonK flashed, 1450kv Emax motor , 4s 5000amp , very heavy but fly very smooth it can handle weight easily .I am really blown away with the quality of this kit. All parts fit perfectly, surfaces are SUPER smooth and the build is as easy as it could get with an ARF foamy. Wings are super stiff, plenty of carbon rods in there.
Only downside: The top hatch is a bit weak at the aft wing spar. Easy fix is to strengthen it with some carbon flats. Also see RCGroups or other forums on this.
Five crowns, will maiden today.
(Setup info: 2830 1000kV, 9x5 HQprop, HK 15178 servos, Plush 60A, Zippy 5000mAh 4S, AR600 for test)