This is a high precision servo which would be best suited for agile and sensitive 3D helicopters. It can be used in a plane, though its precision may not fully be appreciated. Better specd and more precise than a Futaba or Hitec, the MKS DS9660 is a respected servo in Taiwan, Korea and Japan.
Control System: +Pulse Width Control 1500 usec Neutral
Required Pulse: 3-5 Volt Peak to Peak Square Wave
Operating Voltage: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C
Operating Speed (4.8V): 0.13sec/60 degrees at no load
Operating Speed (6.0V): 0.10sec/60 degrees at no load
Stall Torque (4.8V): 51.38 oz/in. (3.7kg.cm)
Stall Torque (6.0V): 63.88 oz/in. (4.6kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400 usec
Direction: Counter Clockwise/Pulse Traveling 1200~1500 usec
Motor Type: Coreless Motor
Potentiometer Drive: Indirect Drive
Bearing Type: Dual Ball Bearings
Gear Type: All Metal Gears
Connector Wire Length: 15cm
Dimensions: 43 x 15 x 28.6mm
Weight: 1.58 oz. (35g) helicopters apply with 400 to 550 class
Hmotnost ( g )
dimensions are wrong
direct from mnufcturer. Specs:
Control System: Pulse Width Control
Working frequence: 1520s / 333hz
(RX) Required Pulse: 3.0 ~6.0 Volt Peak to Peak Square Wave
Operating Voltage: 4.8 ~6.0 V DC Volts
Operating Temperature Range: -10 to 60 Degree C
Operating Speed (4.8V): 0.13 sec/60 degrees at no load
Operating Speed (6.0V): 0.10 sec/60 degrees at no load
Stall Torque (4.8V): 3.7 kg.cm (51.4 oz/in)
Stall Torque (6.0V): 4.6 kg.cm (63.9 oz/in)
Connector Wire Length: 24.0 cm (9.4 in)
Dimensions: 35.8X15.2X29 mm (1.41x 0.6x 1.14 in)
Weight: 32.3 g (1.14 oz)
Mal iyi ama pahal.
5-6 krm oldu salamlar imdilik...Very precise Servo. I unse it in my Zlin 50 for Rudder. Enough Power for that and the metal Gear shows still the same nearly not noticeable slope than at the beginning. Have survived now over 70 landings.Concurent direct de futaba,
command ici parce que tjours un peu moins cher que le prix en europe !these servos have the tightest metallic gearbox I have ever seen... Tighter than their rival MPX Micro Digi. The torque seem on par and this servo does support a direct power source made from 2s A123 (=6.6V) without heating or buzzing. A bit pricey but super high quality servo mounted at the full flying elevator of my 3.5m glider. The other two in my order will control the flaps of my new 5 m glider.
Nearly perfect swash plate servo for an T-Rex 500. Fast, strong, precise and reliable. Fits well to the TR frame. - I use it at 6V in a V-stabi flybarless system.What a great servo fast for tail (rudder)used with 401 work great no issuesI ordered 3 of them for my protos 500. They works perfectly. Very precise and strong for 500 cyclic. I recommend it for all pilot's level. If I build another 500 heli, I would use it again. Thank you HBI am very pleased with this product.
I bought a second set of servo for my 500
(SJM 430 Vbar and Trex 500 Vbar).
Fast, accurate, reliable.
Recommend to the cyclic 500.Received it recently and hadn't the time yet to test it. But i already knew this servo so i can say that is a great servo and very well construted.