The Multiwii SE V2.0 is a gyro/accelerometer based flight controller that is loaded with features. With expandability options and full programmability, this device can control just about any type of aircraft. This is the ideal flight controller for your multi-rotor aircraft.
• Small size, 35x35mm mounting holes
• 6 input channels for standard receiver and PPM SUM receiver
• Up to 8-axis motor output
• 2 servos output for PITCH and ROLL gimbal system
• Can utilize a servo's output to trigger a camera button
• FTDI/UART TTL socket for debug, upload firmware or LCD display
• I2C socket for extend sensor, I2C LCD/OLED display or CRIUS I2c-GPS NAV board
• Separate 3.3V and 5V LDO voltage regulator
• ATMega 328P Microcontroller
• MPU6050 6 axis gyro/accelerometer with Motion Processing Unit
• HMC5883L 3-axis digital magnetometer
• BMP085 digital pressure sensor
• On board logic level converter
• One of the following basic mode
- Alt Hold
- Head Lock
• Optional mode
- HeadFree (CareFree)
- GPS Hold (Need GPS receiver + I2C-GPS NAV Board)
- GPS Return to home position (Need GPS receiver + I2C-GPS NAV Board)
Fixing hole spacing: 35mm (It can be changed to 45mm by CRIUS Distribution Board)
Hole diameter: 3mm
MultiWii SE FC x 1
USB program board x 1 (Mini USB cable required but sold separately)
3Pin to 1Pinx3 cable 100mm x 2
3Pin to 3Pin cable 100mm x 1
More information can be found on the Multiwii Website.
Hmotnost ( g )
Never Buy it from them. they will send you
XZN MWC MultiWii SE Standard multi-Copter 4-axis Main flight con
this board which is very poor and cheaper(US 19) than the item shows in their listing.They sent me the wrong board the 1st time. Did a RMA to replace wrong board and they sent me the same wrong board again. Can't comment on functionality because I've never received what I ordered!Good board for my 20 cm. arm small tricopter flying great with D2822/17 kv 1100 motor and 1,5 Ah lipo pack for about 10 minutes of very fun.Hi All! I've got MultiWii 2.0 installed and running on my Quadro. HobbiKing Rx, HobbiKing 10A ESCs are used. Previously I used HobbyKing Multi-Rotor Control Board and it flied well. On this MultiWii control motors running not fast enough to take quadro off the ground. Even if I move throttle stick to the most up position it does not fly. Can anyone say what is wrong?Nice board flying very well But when I tried to plug the battery monitor on A3 input as shown on file "pin assignments" (lipo directly on this input) I burn the Atmega ...I had to add the divider resistor before input the direct lipo voltage.So be carefull bfore wiring this batterie monitor input (A3 pin).
I put a updated picture of the pin assignments with the rsistors in the file sectionI use this board on a 55cm quad, replacing a homemade combo of Arduino ProMini and 4 single sensors boards... Adding a LZ-GPS was very easy because I2C is brought out on its own pin header. The HK S2 V2 board has the Crius V2 layout and comes with preloaded MultiWii 2.1 firmware for Quad X constellation. Firmware can easily be updated or changed to any other config with the FTDI header and Arduino 1.01 software. The MPU 6050 gyro/acc gives really great and stable flight behaviour with an very smooth ACC level mode never seen before. BMP baro is not state of the art anymore (low resolution), but its OK to get a height hold mode within 2-3 meters. Overall: Great board with good quality, small boards size, totally worth the money. Will buy a 2nd one for my Flydumini as soon as they are on stock again.A good product!!! This comes pre-programmed. But the PID values are all out of boundaries. So you will face a hard time setting it up...bu gne kadar kullandm kartlar arasnda en iyisi.
gps modl de almanz tavsiye ederim.The ever expandable MultiWii controllerThe 0.03 hectopascal maximum resolution of the BMP085 is an optimum enabling the sensor to respond to differences in altitude of 25 cm.
At this days pressure sensors have ~ 10cm. altitude sensitivity!
pin assignments download now [184kb] No File Name download now [184kb] Newbies Guide (By ATXHELI rev. 04/22/201 download now [452kb] pin assignments with Batt monitor resist download now [199kb] Flight-Ctrl ME 2.0 Schematic download now [781kb]