One of the hottest looking aerobatic aircraft around is the MXS-R. Good looks alone are not enough, the Hobbyking MXS-R 20CC has been designed with one thing in mind, awesome and extreme aerobatics.
The quality of the MXS-R 20CC is simply as good as it gets, the airframe has been constructed to keep the flying weight minimal but strong enough to take the punishment of extreme aerobatics. The superb quality covering has been expertly applied and for the final touch, the cowl, canopy and wheel pants are finished in a deep gloss paint. The hardware which includes wheels, fuel tank and carbon fiber control horns is excellent and also chosen to keep flying weight to an absolute minimum. Additionally the model features plug in wings and carbon fiber landing gear and tail wheel assembly.
The HobbyKing MXS-R 20CC performs every inch as good as it looks, naturally it makes for a great sport aerobatic plane but it would be fair to say that hardcore 3D is what the MXS-R has been designed for. The lightweight and precision of the airframe, large control surfaces, stunning looks and top line quality specs make the MXS-R 20CC a must have plane for all aerobatic and 3D pilots!
• Almost Ready to Fly - Just install your choice of motor, battery, and electronics
• All Balsa and Plywood construction
• Carbon Fiber landing gear and tail wheel assembly
• Two piece plug in wings
• Superbly applied, high quality covering
• Full airfoil tailplane/elevator/fin and rudder
• Excellent color scheme for easy orientation
• Large fuselage access hatch
• Optional wing tip side force generators
Wing Area: 50.1dm2
Empty Weight: 2700g
20CC Gas Engine
6 Standard- High Torque Servos
5-6 Channel Transmitter and Receiver
Hmotnost ( g )
Motorsize ( průměr -or- cc)
Rozpětí ( mm ):
SaleWeight ( g )
Rám / PNF / RTF (mm)
IC / 2 : Elec:
This is a very well made airplane.
This MXS-R is also made under brandnames like Aerobeez and/or Flight Models.
The airplane looks a lot like Extreme Flight, only this one is a little bit heavier.
The airframes weight is just above 2 KG (this is without electronics/motor).
I have converted mine to electric. My setup is: TurnigySK3-5055/430kv motor, and 100 A esc with BEC.
Lipo battery is 3700Mah 6S. APC 16x10 propellor. Total weight just under 3200 grams.
I haven't flown it yet, but expectations are high.Hi everyone,
I highly recommend this kit, it is a top quality ARF with strong hardware. I had to reorder due to my learning curve in gas engines. Installed an OS GT-22 with rubber mounting (Dubro) and it is a great choice. Used recommended servos but make sure you put a strong receiver battery (ideally the most powerful 2S lipo suggested).
I'm still in the break-in period with the motor so not completely sure but I'd say this is not a pure 3D model, more a Sport flying but I will try to move weight and maybe use a smaller gas thank. Other than that go ahead and order it for such a low price!Update now that the MXS-R is built.
Hardware spec (electric conversion) is:
Motor: Turnigy SK3 5055 430kV
ESC: Yep 120A c/w 10A SBEC
Battery: 6s, 5000mAh, 40c
Prop: Zoar/JXF 18x8 wood
Servos: 'Goteck' HV Std size Coreless
It all went together perfectly. I used 75mm standoffs to position the motor. The dual elevator servos needed 2mm packers to stop them hitting each other. balance was spot on.
She flies great, ample power and needed virtually no trim. the wheel pants cracked a little due to longish grass but that's a general problem with wheel pants when flying off grass. Handling is great, very little coupling and good post stall handing, no wing rock to speak of. Highly recommended.Top quality kit, rivaling the liked of Extremeflight. This is the exact same airplane that you can buy elsewhere for double the price from the likes of Aerobeez and others.
Quality of the airframe and components really are top notch. The only slight criticism I can level at it is the paint on the canopy does not match the covering very well but that's not a big deal.
One thing to watch when choosing servos: Servo cutouts are for standard size servos, but infill plates for mini servos are supplied. The dual elevator servos ideally need to be quite low profile to avoid them hitting each other. About 22mm from bottom of servo case to mounting tab, max.Wow! What a great flying plane and at such a great price. One of the best looking and best flying planes you can have. I have had many including 3d HobbyShop and this compares to it. Does anything you want and can just Elevator it down to the runway. Check around and you will see Hobbyking has it 100-200 dollars cheaper than other sites. This is a "Flight models" model. I have the green one and know bought this one.
Just want to start by saying, what a great quality kit. All the hardware is top quality with carbon fibre horns and ball joints. Everything fitted together well with a few small adjustments here and there. Being my first balsa kit it was still quite straight forward to put together. The supplied CD contains a basic manual that is some help but leaves a fair bit to the imagination.
I set my plane up as ep with an ntm 5060 380kv motor, yep 100amp esc, 4500mah 6s batt, 18x10 wood prop and towerpro mg996r servos . All that was needed to make it ep was a hk adjustable motor mount.
The only problems with the build being the 2 elevator servos hit together inside the fuse as it get very narrow towards the tail. I fixed this by putting a small block of wood on one side of servo as a spacer. Also a similar problem with the control horns in the rudder touch as you push them though either side so can't go all the way in but I just evened them out and glued them and they seem solid.
No File Name download now [2792kb] No File Name download now [2792kb] No File Name download now [2077kb] No File Name download now [2057kb] No File Name download now [6461kb] Manual MXS-R (English) download now [5784kb]