NTM Prop Drive motors are rock solid performance outrunners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings plus they are QC checked at 14 points, from material processing all the way through to final dyno test.
Because we design and build these motors completely in-house (from 3D/2D drawing to materials sourcing, machining, balancing, final assembly and dyno) we can completely control production and ensure product consistency from design right through to shipping the product to you. The removal of middle-men has meant we can drive better value to the market and retail these motors at factory(our) prices! All performance figures are real and tested on our own motor dynos.
Our QC engineers check and balance each motor before shipping to the HobbyKing.com warehouse.
Model: NTM Prop Drive 35-36A 1800
Max current: 65A
Max Power: 700W @ 12v (3S) / 875W @ 15v (4S)
Cell count: 3s~4s Lipoly
Bolt holes: 18.9mm & 25mm
Bolt thread: M3
Connection: 3.5mm Bullet-connector
Suggested Prop: Prop test data coming soon!A great plane motor up to .30 size.
Hmotnost ( g )
Kv (rpm / v)
Maximální proudy (A)
Výkon ( W ):
Délka B ( mm ):
Může Délka D ( mm )
Maximální napětí ( V)
Hřídel A ( mm ):
Unit Weight (g):
Průměr C ( mm )
Celková délka E ( mm )
Odpor ( mh):
Einfach Super!! Ich habe ihn in meinem EFX Racer mit Zippy compact 35 c 80 Amper YGE Regler und einer Klapluftschraube 8x7 Aeronaut mit Simprop Mitnehmer er zieht 80 Ampere dauer was die Akkus zwar sehr mitnimmt aber er geht wie Schmids Katze. Steigleistung 36 M/sec.
stsguy 27 points - 18/01/2016
SOMETIMES hk GETS IT RIGHT AND WITH THIS MOTOR THEY DID! I bought this motor awhile back and installed it a wing. a small wing of 36 inch wspan and it was a hand full. I was looking for disaster and.... found it. So I installed it on a smaller wing with a list of different size props. 8x6 thru to a 11x6 the 10x10 worked well as any but the 9x6 was ok too. ive been flying planes at 1 to 1.5 lbs and it is scary to say the least. Im adding one to my lateset build and will get back with the stats Its a 64 inch wing at 3.5 lbsGreat bang for the buck! Bought this for my EFX Racer kit. Built a previous kit with the 28mm motor and it was awesome. Cant wait to get this new one crammed in!! For the affordable price these motors are a great option!Haven't flown on this yet - only bench tested. But this one is a beast. Lighter than my E-flite 1250 Kv Power 25 but with more power. I run 8x8 on 4s on the E-flite for 53A. This one went 89 A on a 8x6. I know it is 1800 Kv but still, wow! Will be trying a 6" prop some time. 6 or less in pitch. Will post results on the Discussion tab here or the International Warehouse Discussion tab. Make sure you buy the Accessory pack (as many other good people here have posted). Comes with bullets soldered unlike the G25 I had. Thanks, HK. :)Very strong motor, i used it in the durafly efx racer with a 7x8 apc prop.
Very fast! Look for good cooling and a strong speedcontroller (80A or more).
Current will be 100A at full throttle, so look at your fligthtime, not more than 10 seconds full throttle, then slower to cool up.Cumple con su funcin, es recomendable comprar otro eje por si acaso. No vale como motor pusher salvo si se cambia de lado el eje.moteuur peu fiable 3 vols bruleeExcellent - Using it in a MPX BlizzardReplaced 800kv stock motor with this, and my 40 wingspan Zero screams!! Using 8x6 master airscrew 2 blade.I bought this NTM to replace the motor in my Dynam P-51. I'm running an 9x6 with a 60A HK ESC pushed by a 4S 2600 MAH LiPo. This plane MOVES! It gets warm when flying at WOT, but nothing that would do any damage. This motor is a power house. I've got nothing but good things to say about it.