The OrangeRx GA7003XS has all the properties and features of the original FASST compatible receivers but this one supports SBus and also includes the well tried and tested OrangeRx 3 axis stabilizer system. This stabilizer system has independent gyro gain control for aileron, elevator and rudder. This stabilizer will smooth out these 3 controls and make the model easier and much smoother to fly, especially in rough air conditions. No seperate mixer is required as this unit supports dual aileron, V tail mixing and delta mixing. They also will accept a wide range of input voltages from 3.6~8.5V which is great if you want to use LV and HV type servos.
The S.Bus functionality is an excellent feature for use with multi-rotor flight controllers such as the KK2.1, APM, MultiWii and others. These single line connections remove the weight and mess of additional wire leads for each individual channel. This is ideal for use on small frames where space is at a premium and keeps all the wiring neat. It is also very handy for large aircraft and gliders where you are using lots of servos in the wings etc and once again keeps the wiring very neat and tidy.
Compatible with the following Futaba FASST 2.4Ghz air systems such as TM7, TM8, TM10, TM14, 6EX, 7C, 8FG, 10CG, 12FG, 14SG, 18MZ etc.
• Lightweight (16g)
• Compatible with FASST 2.4Ghz air systems
• 7 channels
• Built in 3 axis stabilizer
• Dual aileron, V tail mixer, Delta mixer
• Compact design (55 x 32 x 14mm)
• Twin antenna for diversity and long range
• Specified Range: 1.5km+
• Improved anti-interference capability
• SBus output support for expanding servo channels
Input Voltage: 3.6~8.5V
Sensitivity: About -96dBM
Dimensions: 55 x 32 x 14mm
1 x OrangeRx GA7003XS receiver
1 x Plastic srewdriver for adjusting stabilizer gain
All OrangeRx receivers come with a 12 month warranty. This is not a Futaba receiver, nor is it a copy of a Futaba receiver. Futaba and FASST are trademarks of Futaba Co (JP).
Hmotnost ( g )
Kv (rpm / v)
Maximální proudy (A)
Výkon ( W ):
Délka B ( mm ):
Může Délka D ( mm )
Maximální napětí ( V)
Hřídel A ( mm ):
Unit Weight (g):
Průměr C ( mm )
Celková délka E ( mm )
Odpor ( mh):
OMG!!!! This is by far the easiest, cleanest install and great working Gyro i ever had. Binds directly to my 18SZ and works like a charm!! My Bravado flies so smooth even in windy conditions.
Will definitely buy more!GREAT DEAL! WORKS AWSOME, EASY TO USE AND IS REALLY COOL TO MESS WITH AND TRY NEW THINGSI have received a new one. This one works perfectly. A very good product ! But 4 stars only because the first one didn't work : sorry !Arrived defective. Powers on and binds to Futaba 8FGS, but does not output anything on any channel. No servo control, no signal to ESC, doesnt matter if you use Multi or 7CH modes. Only giving two stars because HK refunded me promptly.
montage et configuration sans aucun problmeMy unit doesn't work : I bind it on my Futaba T9 but no servo moves ! I don't understand what happens. And nobody answers my RMA ...This receiver - stabilizer works well except for one issue which has been observed by at least two users now. All channels will stop working and responding to the transmitter, and no signals sent on the SBus if channel 7 has about -5pcnt input. Sometimes it will also go crazy and send large signals to other channels under this condition. It will work perfectly if channel 7 is outside the range -2pcnt to -8pcnt such as if channel 7 is exactly zeroed. This was discovered when trimming channel 7. This occurs in both 7 channel mode and multi-mode, with Futaba SG14 and Futaba SG18 transmitters and with two different receivers.
there may also be a problem under some condition on Channel 6.Werkt niet met de settings voor 2 airlerons.
Normaal is kanaal 1 en 7 airleron.
Echter setting 2 airlerons dan wordt kanaal 1en 6 samen geschakeld als airleron 1
7 blijft airleron 2.
Dus geen mogelijkheid om de kleppen te gebruiken.
Dat is bagger, slechte eigenschap.
In de modus een airleron is kanaal 1en 7 airleron en 6 de flaps.
Kanaal 5 schakeld de giro in en uit.
does not work with the settings for two ailerons.
Normally channel 1 and 7 aileron.
However, setting two ailerons than channels 1 and 6 connected together as one airleron
7 remains airleron 2.
Therefore no possibility to use the airbrake or flap,s.
That's is bad habit.
In mode one aileron are channel 1 and 7.
channel and 6 aileron flaps.
Channel 5 Giro switched on and off.
That is OK
Dion WijnenNeat tidy Futaba FASST Compatible RX with 3 Axis Flight Stabilizer.
No messy wiring, lightweight, compact, full range apparently 1.5km.
Fully compatibly with my Futaba 6EX.
Easy to install, binding was quick and easy.
Something not mentioned on the HK page is it that it can be switched ON / Off inflight through Channel 5 on your TX just like the other Orange 3 axis stabilisers do, a really good feature.
Instructions are in tiny print and not the best English but understandable.
On mine the 3 Axis adjustable Potentiometers were not properly lined up with the holes in the plastic cover, found myself digging around blindly to adjust them, not good as the adjusters are only tiny plastic screw driver slots. It does come with the adjuster screwdriver but didn't fit mine properly. Found it quite difficult adjusting the sensitivity even after reading the instructions.
Have scanned the instructions will try to upload.
Overall looks good value for money.excellent receiver and gyro. used it with 3dhs 75" and EF 83" mxs. much better than using separate receiver and gyro.
ended up buying 4 more.
the included manual seems to provide adequate info.gyro switch on/off on channel 5.