The all new RX3SM Micro Flight Stabilizer with integrated OrangeRX DSM2 compatible 4CH 2.4Ghz receiver is ideal for Micro models. It eliminates the need for using a separate receiver in your model, not only making installation more tidy and convenient but allowing you to simply bind with flight stabilization! The RX3SM DSM2 compatible stabilizer provides support for V-tail & Delta models and also offers a remote ON/OFF feature that can be controlled via your transmitter's AUX channel.
Utilizing a single high precision 3-axis MEMS gyro, the RX3SM DSM2 compatible stabilizer is capable of stabilizing flight on just about any fixed wing aircraft! It provides added stability by automatically correcting the aileron, elevator and rudder channels in flight. This compensates for unwanted changes in the airplane's attitude due to wind and other factors. In short, it makes your airplane much more stable in flight!
The RX3SM DSM2 compatible stabilizer has been designed specifically for use in Micro models, weighing in at a scant 10g only! The size has been perfectly matched for use with our Durafly Mircro series. It is also compatible with any other Micro model utilizing 3 pin Micro Molex connectors with 1.25mm pin spacing.
This unit is very simple to install and use. The adjustable gain settings are pre-set to 50% offering mild stabilization. You can easily adjust the gain for each channel as desired to increase or decrease the compensation for the respective channel (AIL, ELE, RUD).
Because we design, test and manufacture these units completely in-house (from 3D/2D drawing to materials sourcing, final assembly etc.) we can completely control production and ensure product consistency from design right through to shipping the product to you. Also, the removal of middle-men has meant we can drive better value to the market and retail these units at factory(our) prices!
• Perfect fit for all Durafly Micro Models
• OrangeRX DSM2 compatible 4CH 2.4Ghz integrated receiver
• Micro Molex 3 pin connectors with 1.25mm spacing
• Capable of stabilizing flight on just about any fixed wing aircraft (including V-tail/Delta models)
• Remote ON/OFF feature that can be controlled via your transmitter's AUX channel
• Supports 3D flight without undermining stability
• Independent gyro gain adjustment for aileron, elevator and rudder
• Easy-to-access gyro reversing switches on front of unit
• Compact and light weight design
Integrated Receiver: OrangeRX DSM2 compatible 4CH 2.4Ghz
Gyro: 3-Axis MEMS
Input Voltage: 4.8-6.0V
Signal to Servo: 1520us
Servo/ESC Connection: Micro Molex 3 pin with 1.25mm spacing
*Note: User manual available for download located under the "Files" tab below
1) This is not a Spektrum DSM2/X product, nor is it a copy of a Spektrum DSM2/X product.
The Spektrum and DSM2/X brand is a trademark of Horizon Hobbies USA.
2) This is not an underground black market fake Spektrum product. OrangeRx quality is guaranteed.
Hmotnost ( g )
I don't know if this is a good product or not . My issue is with the purchasing and retun policy of this company. You have warehouses in the US then you should accept credit cards and stop with the 3rd party garbage. Horizon hobby does not do this Amazon does not do this. So long Hobby KIng I be sure to pass this along to everyone I fly with.This is a great little RX. The stabilization really helps in the wind. Be sure you note that this is the micro connector, not JR/Futaba.Hi all,
not so satisfied so far with the receiver as the servo throw is too low for an agile mirco slow flyer which seems to me to be the typical use case for this kind of receiver. See also https://www.youtube.com/watch?v=UPoFwtcJPFw where the problem is visually shownThe second comment on this. In the first, I couldn't get a signal from the ESC to the unit (no flashing LED). The problem was the voltage polarity to the receiver. I used a HobbyKing Molex 1.25 pigtail to connect to the Turnigy ESC. I simply connected the red on the pigtail to the red on the ESC, etc. This was wrong! I reversed the white and black and it works! If you went by what the WIRING section of the manual says you would be wrong! It is poorly written and refers to "inner pins" and "pins on the outer edge". Maybe a Chinese translation to English that didn't go well?Habe diesen kleine Empfnger in der F16-Wurfgleiter verbaut. Mit 2x1,9g Servos und Aussenlufer mit 3 Zeller Flugakku. Alles zusammen ca. 80g. Das Ding ist ohne diesen Kreisel fast unfliegbar. Mit diesem Empfnger liegt der kleine Flieger wie ein Brett in der Luft. Super, sehr zu empfehlen.Bought to put on my eflite inverza because its twitchy in wind. After finding out the wiring instructions are incorrect I corrected the wiring and the rx works well. I just need to fine tune it. As the wiring instructions say all signal wires are supposed to be towards the center of the 4 molex cluster, which is incorrect. The wires must be ground, pos, neg across the top and bottem if the molex connectors are at the top of the rx. Oh and on this plane the polarity of all the wires must be flipped. Its a pain but in the end its worth it.Not very pleased with this device. The gyro simply does not give enough output to provide effective stabilization of a model aircraft. I fitted one into my little SPAD XIII and with gyro set to maximum on all axes it has vertually no effect on models stability. I purchased a second RX3SM incase the first was faulty but its performance was identical. The larger RX3S device produces much more control resonse to rotation. I would rate the RX3SM as useless and not recommend it to anyone.Put on a micro slick Durafly. Very nice. Good job!Highly recommended, Have bought a few of these and never had a problem.
Setup is a breeze.ideal para pequeos modelos indoor