The Quanum power distribution board is a 3-in-1 device that simplifies even the most complicated multirotor builds.
The PDB has two built in super clean 5A UBEC’s one set at 12V for your FPV gear and the other adjustable from 3-20V perfect for powering your flight controller or other gear. The 2oz copper double sided PCB can handle 80A of power and the Ubec’s can take up to a 6s. There are dual output pads for the Ubecs and 8 positive and 8 negative pads for the power distribution. The overall size is the standard 52mm with 45mm holes for drop in mounting to most multirotor frames.
Simplify and tidy your multirotor builds, well increasing reliability and decreasing weight with the new Quanum 3-in-1 power distribution board.
In Quanum you can trust !! Don’t get caught using an inferior PDB, the Quanum PDB was spec built using 2oz copper giving a true 80A rating, not found on similar PDB elsewhere.
Mounting: 45x45mm holes square (3mm holes)
Ubec 1 output: 5A 12V
Ubec 2 output: 5A 3~20V adjustable
Hmotnost ( g )
I've used 2 of these on 2 hexacopters with FPV!! It's awesome to distribute power to my 3S system (6 escs), to my FPV transmission system and it's awesome it has an adjustable 3V - 20V output that I used to power my 3.4V LED system with a switch (6 LEDS)!!. It's a must have product for Quads or Hexs. I really recommend it.Works great except my adjustable BEC appears to be stuck at 10V. Not really an issue for me as I have nothing that has to have 12V and it will all run fine from 10V, but could it would have been nice just in case. This is significantly bigger than the NAZE32 which isn't a problem for the quad I put it in (its huge and has heaps of space) but I'll be getting a smaller one next time.Eigentlich wirklich ein super Board fr einen 250er FPV Racer! Jedoch nervt mich das das Boti fr die BEC Spannung keine Anzeige hat, auch keinen Anschlag mit Min und Max. So ist es schwirig die Spannung einzustellen. Knnte man mit einem LED Strip machen um nicht was zu zerstren!This device is great. I put the 12V BEC on an O-scope and measured less than 25mV ripple on it. It gives a nice clean power source for my FPV gear. I highly recommend!Hi there, all things considered, this is a good solution to keeping one's wiring tidy and providing two clean power outputs. The board works very well stacked below the FC on standoffs. I measured the two outputs and found them both within spec. The build quality is good. The only negative was that the unit I tested was audibly noisy, in that it emitted a constant low frequency sound that could be heard from a few feet away.
To sum up I can recommend this unit as it does what it says it should. The price is a little high but I guess we all need to make money.
Woks fine no more cbles anywareI have no idea for power dist.... But good and cheap for ubecProduct is of decent quality and works as described. Haven't tested how clean the power is for video and transmission.Guys this PDB is legit. Power output is clean on ubec 1 and 2! Check out my FPV ground footage in discussion tab. I have 12v output plugged to my Tarot brushless gimbal and GoPro3plus plugged to 5V power output of gimbal control board. Higher voltages are stepped down to 12v or adjusted with the pot. Ubec 1 powers my FPV gear, Ubec 2 lights up my 12v LED's. 10 min flight not even warm. Very happy with this purchase and worth every penny IMO. I'm going to get another one soon :) Thanks Hobbyking!! Here's a link to the video . . . bit.ly/QuanumPDB