RC Sailboat-SurmountA beautifully crafted R/C sailboat, fully built and ready to run.
All required items are installed, including mainsail winch, steering servo and all rigging, sail and hardware. All you need to do is add your own receiver and battery!
Boat hull is based entirely on an ocean going racing yacht and moulded in fibreglass with a perfect gelcoat and enamel painted finish.
Don't be mistaken in thinking these boats are slow and boaring. In a stiff breeze they can be extremely quick and perform turns rapidly, proving to be very exciting.Spec.Length : 800mmHeight : 1520mmWeight : 1.4kgArea of Sails : 0.25m2Ballast weight: 1.3kgDraft from the waterline to bottom of keel: 300mm
Rig Height from the deck to the top of the mast: 1110mmRequired.
Radio System (2ch)
Receiver battery.Note: Please ensure you fill the keel ballast to 1.2kg or heavier. Lead shot, bearings or bolts/nuts will be sufficient. Keeping them in place with epoxy.
Kapacita ( mAh )
Hmotnost ( g )
nice quality. love the look of it.Stunning boat well packet! Insturtions where a little hard to follow but once step up its great! Easy to transport just loosen mast ropes and your donevery good boat, sails well but ballast is to small to fit required weight, recomend lead weights to balance it outSurmount dotarl w kilka dni z magazynu europejskiego. Brak jakichkolwiek uszkodzen. Balastu olowianego weszlo okolo 970 gram. Jedynie do czego mozna sie przyczepic, to pekajace plastiki mocowan lin.as already said, get ready to use the pictures on the website to rig your boat. Directions are not too useful. I completely filled the ballast bulb with lead shot and taped over the hole,no epoxy needed. Watch some youtube videos for some idea of rigging. I experimented and found that the jib boom and mainsail boom need to be parallel, that the sail should pull away from the boom about an inch or so to create a good foil, and that the sails must be similarly curved to direct air properly. The trailing edge of the sail needs to be relatively taunt to create a good foil; make sure to plug the hole in the transom with the plug provided, and use the decal to seal the plate over the rudder servo once you get things setup, otherwise you get some water in during sailing. I used an aircraft receiver (orange rx from HobbyKing) and a 4.8V NiMh battery pack to power the servos and receiver. I set the travel to 30pcnt for the sails on my aircraft transmitter and it seems to work great. This is a fun little sailboat and a good bang for the buck!I ordered the Surmount on monday, delivered on wednesday (EU warehouse), so excellent postal speed.
The Surmount came nicely boxed with foam at the ends for protection. Accesoires well packed in boxes and bags, no missing parts.
The manual is in Chinglish, translated by google into eh...eh... there are words and pictures in there, so shut up and start assembling.
The mast connector didn't fit but was jammed into place anyway, a light bend but it'll work as required. Mast and booms are black, nice. Lines were nicely winded on cartons and everything looks excellent, specially the hull.
I replaced all the lines for dacron kite wire (25dan) as the stock wire seems a bit flimsy. The dacron also slides more smooth through the deck.
Bulb filled with soft lead from the diveshop (they have bags with 1-1,5mm leadshot) Filled bulb showed aprox.1100 gram on the scale, filled the hole with epoxy and epoxied the bulb-fin-hull connections. Made a small wire in the drain plug to prevent loss and covered the rudder servo to prevent tangled up line in there. It's not as perfect as a 250 dollar boat....cause it isn't :-) but it's except the radio and lead for bulb completely RTR, upgrades are not mandatory at all (didn't sail it yet)
Would recommend and buy again.
Now waiting for epoxy to dry and go sailing.Received my Surmount and was impressed with the quality and ease of the build. I could only get 945 Kg of #9 lead shot in the bulb but it sails very well. I would recommend this sailboat to any one that wants an inexpensive sailboat that performs well. I don't race but love to sail around the small pond I have close to me. Most days the wind is 5 t0 10 MPH and the boat can get and go and not lean over to much. Thanks to HK for providing such a sweet sailboat for a very affordable price.Ich habe die Surmount vor kurzem gekauft und bin mit eigentlich recht geringen Erwartungen an die Sache rangegangen. Es sollte ein Segler fr zwischendurch sein und das ist Sie auch, aber auch nicht mehr.
Es handelt sich hierbei definitiv nicht um ein Wettbewerbsboot sondern um einen reinen Fun - Segler. Das Paket kam unbeschadet bei mir an und alle Teile waren vorhanden.
Der Kiel wurde mit 1kg Bleikugeln 4,4 mm gefllt und mit Epoxy vergossen. Passt.
Wichtig ist, dass die Schraube welche den Rumpf mit der Bleibombe verbindet von echt miserabler Qualitt ist, hier lsst sich jedoch leicht Abhilfe schaffen indem man die Teile einfach mit Epoxy verbindet.
Alles in allem sind Preis Leistung hierbei ganz okay und mit ein wenig Geschick lsst sich aus dem Schiffchen auf ein recht passables Gefhrt machen.
Anbei noch ein Video von der Testfahrt: Die Holzverkleidung ist selbstgemacht und gehrt nicht zum Lieferumfang :-) http://youtu.be/CBjj1_aOcmwRifinitura non eccellenti, ma considerando il prezzo un buon prodotto.
dont buy this item from hobby king as its totally fit for the bin,dont ask hobby king for help as they are totally unprofessional.this item is not fit for purpose,