Tarot needs no introduction, their name is synonymous with quality and their 2 axis ZYX22 gimbal controller is no exception.
The Tarot ZYX22 Brushless gimbal controller is unique from all the other run of the mill BLGC on the market, they removed the FTDI chip from the board to save size and weight, but is just as easy to use with the included USB adapter. And Tarot’s computer user interface for setup and tuning (if required) is the easiest and most intuitive seen yet. The Tarot packs in more options, like support for rate mode or position mode as-well as custom initial pitch angle, and support for standard RC input as well as SBUS and Direct DSM2/DSMX input via a satellite receiver. The Tarot ZYX22 is simply the most refined brushless gimbal control and IMU on the market and perfect for the T-2D gimbal or other 100-300 gram camera gimbal systems.
• Supply voltage polarity protection and voltage compensation
• Short-circuit protection
• custom initial pitch angle
• Sensitivity parameter adjustment support and software
• Supports joystick rate mode and position mode
• Dual 32-bit high-speed ARM core processor
• Easy to use software
Working Voltage: DC 7.4V ~ 14.8V (Recommended 12V, three lithium battery)
Working current: 200mA-500mA (power supply voltage and the motor related)
Working temperature: -15c ~ 65c
Processor: Dual 32-bit high-speed ARM core processor
Sensor: Three rotor MEMS gyroscope rotor MEMS accelerometers
Maximum angular rate: 2000 ° / sec
Maximum acceleration: 16g
Control frequency: 2000Hz
Motor drive frequency: 20KHz (no noise smoothing drive)
Control accuracy: 0.1 deg
Control angle range: -45 ° ~ 45 ° (roll), -135 ° ~ 90 ° (tilt)
Power Interface: DC 7.4V ~ 14.8V (Recommended 12V, three lithium battery)
ZYX3 rotor gyro USB cable group × 1
Two-axis gyro sensor head × 1
Two-axis gyro head master controller × 1
USB computer interface x 1
ZYX22 brushless gimbal controller
Kapacita ( mAh )
Hmotnost ( g )
good! Tarot ZYZ22 GOPRO Brushless Camera Gimbal Controllermi era capitato di invertire l'aggancio dell'accellerometro su un kit completo tarot 2D e per mia sorpresa vendevano anche solo l'elettronica di ricambio. Invece di riacquistare tutto il gimbal ho riacquistato solo l'elettronica che identica a quella a corredo con il gimbal. Per sostituirla basta aprire l'alloggio dell'accellerometro e via. Non ci sono controindicazioni. Se pu essere fatta una nota negativa, i contatti sono facilmente invertibili e scambiabili, infatti mi capitato di bruciare la scheda inserendo il contatto dell'accellerometro nell'apposita presa per collegare l'usb. Si bruciato sia l'accellerometro che la scheda.It works but LOTS of small nagging issues.
1. No standard servo connectors. Micro connectors on the board (1.25/Molex) so you should purchase adapter or solder wires directly. These are not mentioned in suggested to buy section, needless to say. Annoying, especially for post orders.
2. USB interface is based on old Prolific chip which is NOT supported in Win 8. The other chip will work but interface socket on board is 4 pin 1.25 Molex with unlabelled pins. Had to dig up my Win7 notebook. Annoying.
3.No protection case for sensor. Sensor wire is to short to mount it on gimball for larger frames.
4.Long init after power is plugged.
But it work.Works perfectly! But the sensor cable should be longer...
Mounted mine on the HobbyKing Brushless ActionCam Gimbal With 2208 Motors and 3K Carbon Construction and GOPRO Hero 2.Nice little controller for the price, just a bit hard to tune up, but once it is tuned, I think it works well. I had to order my replacement after burning up the first in a failed firmware update process...OOPS!
No File Name download now [2kb] No File Name download now [594kb] No File Name download now [35kb] 994156982X437860X40.JPG download now [97kb] Tarot 2 ejes Manual spanish download now [533kb]