TURNIGY AerodriveXp SK SeriesAerodriveXP SK Series motors are designed for those who want the very best in outrunner technology for their R/C plane. Typically an efficiency improvement of around 8-10% can be seen over similar classed motors. This is in part due to the following;Stator Laminations: .2mm
Magnet Type: N45SH
Bearings: Dual oversize (Japanese)Model: SK28-36 750
Resistance: 130m-OhmIdle Current: 0.4AShaft: 4mm
Rated Power: 262WESC: 25A+Cell count: 2-4Suggested Prop: 11x8~12x6
*Includes mount and prop adapter accessories (not shown)
Hmotnost ( g )
Kv (rpm / v)
Unit Weight (g)
Maximální proudy (A):
Odpor ( mh):
Maximální napětí ( V)
Výkon ( W )
Hřídel A ( mm ):
Délka B ( mm ):
Průměr C ( mm )
Může Délka D ( mm )
Celková délka E ( mm ):
Muito bom, com um spiner muito bom mesmo, recomendoI was going to use these in a boat, the Kv is good, drives a 40 mm brass prop with ease on 11.1 volts in a 1.3 metre patrol boat hull excellent scale speed. draws 14 amps on a Raboesch 40 mm 3 blade prop.
They are noisy, the bearings are gritty and the bell is not concentric with the shaft, i get 0.5mm run-out, this means lots of noise and vibration especially at a certain RPM which must be a resonant frequency.
I can live with the bearings they were easily replaced but the bell run-out is not good enough
Sorry Hobby King but this motor needs better quality controlDon't waste your time and money on this one.
It is very noisy.
When I speed up the motor without load.
The noise out with vibration.
It is looks like unbalanced.
I test the motor using 12x6 propeller only 133wattA11x6 propeller 0nly 132watt.
It is not a 262 Watt motor look like.
So the performance is quite low.
Sorry but have to give this only 2 stars. Yes the motor works but that's about it! You can't use 3S because you get virtually NO power out of it and if you go up to 4S to get anywhere near 200watts or more they start to get VERY hot after only a couple minutes. I was gonna use this in a twin setup P-38 but found other motors. I have other SK motors and they've been fine, just don't waste your time and money on this one.Parameters of winding resistance for this motor, are incorrect.
I have two.. They are exactly equal.
Measured resistance is 185 miliOhm.
Motor is "star" type.
It is quite useless for any higher power.
I may suggest, not to try to exceed 10 amperes.
You may use 4s or even higher voltage... Anyway, for 80 gram motor it seriously underperforms, and it will burn if prop is too big.This is perhaps the strangest motor I have ever used. I put it in an E-flite Mini Pulse with a 12X6 on 3s. It would barely fly it. When I tested other props on it, i had to go all the way to 14X7 to get adequate thrust. I ended up using 4s and 11X8 to get good performance.This is a good motor.Should be run on 4s for best performance.Good motor, but a bit too heavy, The price is good !tres bons moteur.moto planeur de0,9Kg.alloy folding spinner 50mm.pales 12/10.rhino 1750-3s.planeur monte a la verticaleIndeed, wrote to avoid the review:
Engine bearings are not good, noisy operation.
Circuits mounted on the screws are long and meke, allen is now worn out.
Choose another engine waste of money.