Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today.
The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.
The Turnigy SK3 motors are suited to modelers who are seeking a qualitymotor without compromise.
Internal resistance: 0.052 Ohm
Max Loading: 28A
Max Power: 375W
Shaft Dia: 4.0mm
Bolt holes: 25mm
Bolt thread: M3
Motor Plug: 3.5mm Bullet Connector
Hmotnost ( g )
Kv (rpm / v)
Maximální proudy (A)
Výkon ( W ):
Délka B ( mm ):
Může Délka D ( mm )
Maximální napětí ( V)
Hřídel A ( mm ):
Unit Weight (g):
Průměr C ( mm )
Celková délka E ( mm )
Odpor ( mh):
So disappointed: The SK3 3530 out of the box looks like quality construction but I needed to reverse the position of the shaft. Done it before should be no problem right? This motor does not come with an allan wrench like the Eflite motors do, after selecting the proper wrench size and getting a good tight fit, the set screws stripped out because they were too soft, that's it, the motor is now useless 5minutes out of the box, maybe stick with Eflite if you anticipate needing to reverse the shaft position."A leap forward in quality" WHAT A JOKE. I bought 4 of the motors, initially one was faulty (Bad bearing). Hobby king replaced it. Now, another has failed. I'm staying away from cheap crap with projects I care about. I would advise you to do the same.I use this motor for ssc combat. 4 cell 2650 mah 40 c batt. 8x3 ma combat prop. 60 amp plush esc. This combo flys circles around glow powered ssc combat planes. Give it a try you won't regret it.Few measurements of static thurst:
GWS sw 9x4.7, 441w,1200g; (Best power, 1500 mAh 3s 20 c is on limit!!!)
Graupner e 8x4, 300w, 840g; (Best efficiency)
APC e 8x6, 420w, 780g; (lost efficiency not a good choice)
GWS sw 8x4.7, 420 w, 1010g; (More power if you need, but lost efficiency!)
Excellent for 500-600 g 3d, with avarage half throtle 10-12 min on 1500 mAh (with the help of wind :-)), 3s with graupner prop , or best power with GWS sw 9x4.7 if you have enough accu power with low weight.I just wrote a review yesterday but I have to write this, with the smallest carbon fiber folding prop that can be purchased here that is the 9,5x5 size this motor draws 32amps static on the ground at 12500rpm, and in the air 28amps 13500rpm 10,2v... What the hell read the description, what is written there is what you get. Amazing motor!Had my first flight with this motor with a phoenix 2000 glider. The plane comes with a folding 10x6 prop, too much for this but here is some data, will get smaller prop.
tgy super brain 40a data with 2.2 25-50c nano:
no load current 3.3a 20k rpm
10.6v 49a 10800rpm on the ground static
10.5v 43a 11700rpm in the air.(about 100-110km/h)
note that on 80pcnt throttle amp draw is 25-26a at 10600rpm, so with a smaller prop it spins like there is no tomorrow for sure.
Will get smaller prop but its a really great motor, will buy sk3 or ntm in the future.Wonderful little motor, found it ideal for my Bixler 2, turning a 7X5 APC style prop on 2200 mAh 3S battery. Draws 260 watts at full throttle.Have not run the motor yet, but I am impressed with the packaging, accessories, and build of this motor. It would be nice if the motor came with instructions as to whether the shaft is reversible.This motor is great! I paired it with a Turnigy Trust 45A ESC and use a 10x6 folding prop. It is giving amazing power and stays cool even under WOT with no air flow! I am running it on 3SSto usando questo motore con un elica 10x4.7 p, 35 amp esc, e batteria 1800 40c lipo 3s batteria a met gas ha inviato il mio yak 54 in piano verticale di circa 1000 metri in meno di 30 secondi. dopo il volo, il motore e esc erano freddi.Questo motore efficiente e di ottima qualit, vale laa pena l'acquisto.
another view from mike rimfir.10 vs sk3 download now [1367kb] rimfire.10 vs sk3 3530 1340 from mike download now [1428kb] SK3-3530(DT3007-14P) MOTOR (edited).pdf download now [131.66Kb]