Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today.
The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.
The Turnigy SK3 motors are suited to modelers who are seeking a qualitymotor without compromise.
Internal resistance: 0.045 Ohm
Max Loading: 33A
Max Power: 430W
Shaft Dia: 4.0mm
Bolt holes: 25mm
Bolt thread: M3
Motor Plug: 3.5mm Bullet Connector
Hmotnost ( g )
Kv (rpm / v)
Maximální proudy (A)
Výkon ( W ):
Délka B ( mm ):
Může Délka D ( mm )
Maximální napětí ( V)
Hřídel A ( mm ):
Unit Weight (g):
Průměr C ( mm )
Celková délka E ( mm )
Odpor ( mh):
Good motor for the price.Smooth running, good quality.
Testet 8x5 sport Propeller. Unless it is an "E" Proppel or a bigger one a 8x5 is too small. In Comparison with motor size and amp capabilitiesMotor has terrible vibration and it is unusable. Even with no propeller it makes strange noises. Bearings or shaft is bad. I will need to buy some other more quality motor...Flies in my Cosmic Wind<br>
On 3S1P 2200mAh<BR>
With an APC 8x6E prop - 384W at 34A<br>
With an APC 8x8E prop - 430W at 43A<br>
On 4S1P 2200mAh<br>
With an APC 8x6E prop - 599W at 41A<br>
Very nice motor and I highly recommend these as a very good value. Nice accessory pack with prop adapters for front or rear mount and nice mount. 378Watt; 36 amps with 2200mAh 30C Lipo and 9x4 APC (genuine not copy) prop. cruise (50pcnt throttle over five minutes) I get about 135W or - a 10 inch prop beyond the safe limit, but in reality the RPMs are likely well below theoretical, unfortunately I don't have good enough lighting to get a reliable reading from my prop Tacho. Powers my 820g AUW 1000mm wingspan scratch build Spitfire perfectly, great power at cruise, and unlimited vertical at less than 3/4 throttle. Handled a straight in WOT crash on first scratch build without a scratch... loads of mud cleaned out with HOT water jet, WD40 soak, and machine oil lube ... makes a bit of bearing noise now but runs great ... two dozen flights since and going great!Current draw with a 8x3.8 prop = 34 amps (peak). Seems to be the recommended prop for this motor. Haven't checked the flight performance yet.Ein Qualitativ hochstehender Antrieb. Sehr schn verarbeitet, smliches bentigtes Zubehr inklusive. Sehr gut verpackt, verwende ihn in einem You can Fly von Hype, zusammen mit dem 40A BlueSeries Brushless Speed Controler als Ersatz fr die abgebrannte Originalausrstung., 10*6, 35-70 3S 55A , 3 0.35 1 0.25, 4 0.35 , .Hi, im using it with turnigy plush 40a and 11x6 carbon fibre folding prop on my phoenix 1600 glider , it is super power full , very pleased with it .you cannot use full power running a 10x6 folding prop. i just burn my motor. use 9 or 8 inch props with this motor. oh well, would be nice if prop sizes were tested to go with the motor.