Turnigy introduce the Min Power Distributor Ubec suited to 30cc plus gas powered models.
This unit has great features, which include: Dual battery input, 5v isolated linear RX BEC, 30 Amp voltage adjustable Ubec on all output channels, 8 channel RX input with dual outputs on each channel - simplifying dual servo control surfaces.
Great inclusions are the independent 5V linear regulator providing a separate power source for the receiver, optically isolated CDI power & in built remote ignition kill. Receiver, Servo & CDI power sources are completely isolated from each other.
This is the first Power Distributor system to securely nest the receiver within the power distribution 'block' thereby shortening cable runs, adding protection to your all important receiver & speeding set up time.
• 5v Linear RX BEC
• 30 Amp Servo UBEC
• Users adjustable UBEC voltage
• 8 (+1 CDI cut) input channels
• 16 output channels
• 5 Status check LEDs
• Padded receiver tray & Secure mounting
• CDI isolated power
• CDI remote ignition control (remote cut)
• CDI power status indicator light
• CDI power output terminal
• CDI voltage monitor LED
Optional: Input/output voltage display with external power switch
Input Channels: 8 (+1 CDI Cut)
Output Channels: 16
Input voltage: 7-13V
Servo UBEC Current: 30A (40Amp Burst)
Output voltage: 4.8-9.7V (user adjustable; Default is 5.2V)
RX power: 5v linear bec
Working temperature: -20 to 85 degrees c
Dimensions: 116mm x 88mm x 13mm
Kapacita ( mAh )
Hmotnost ( g )
Top, fr den Preis unschlagbar !!! Betreibe eine 3m Bella damit vllig Problemlos. Spannung einstellbar, Zndung ber die Weiche ein und ausschaltbar mehr geht nicht TOP !!!
Warte das sie wieder kommt, brauche noch 2 Stck davon....
Bitte HK schnell wieder auffllen !!! :-)IT has not LCD SCREEN. IT HAS FAKE SCREEN. There is a Turnigy writing on the fake screen. Also a led is shining back side of the fake LCD. Another functions are ok. You can buy another version of this power distributor that it has almost the same functions from another stores cheaper than hobbyking.Seemed to be a great product, all worked as it should initially, after three flights, CDI kill switch stopped working, red light flashes indicating less than 4.2V input no matter what battery is connected and the switch is inoperable.
Fitted on a Yak52 with a RCG 26cc gas engine.
I will now have to purchase a CDI kill switch.Be careful to isolate this board from vibrations on the larger planes. My opto for the ignition control came loose from the board in my Sbach 34pcnt, 35cc, because I had the screws down too tight on the rubber grommet mounts. Bad solder joint. The ignition randomly shuts off (sometimes while in flight!). I'm going to isolate the board and receiver in foam and use Velcro to hold it in the plane. JohnnyBI have purchased 3 of the original 3 panel design panel units. I have installed them into 3 of my giant scale planes. The new panels are a single plastic box. They are easy to use and they performed as intended.
CAUTION!! One of the 3 panel design units failed and I lost all power on my 84 P-51. What I found was one of the 2 ribbon solder joints fail on the main BEC that is located on the bottom panel failed. I was able to repair the remaining units by removing the top 2 panels and repairing the ribbon solder joints. Make sure to get the solder to flow to both sides of the panel. It was a simple repair but why should we have to repair them to ensure we dont lose our planes.
Come on Hobby King Pick up your game!!!!
PS I havent used the new design yet but I do hope they have resolved the problems.
This Bower box works Beautifully, But always remember to leave your assigned kill switch down when you turn on your transmitter and do this before powering up your Power Distributor, Then turn on the power distributor and your kill position will always be down to kill the CDI, This sequence is necessary unless you don't care where the kill position will be. This is a built in Safety feature to always start with the system in the kill position. Hope I made it clear to avoid confusion. Happy Flying ! RonGreat product awesome price for this product. Only one thing could be made better.... an voltage display fr the bec adustment or an DIP Switch with steps and not an potentionmeter...
But again an awesome Product.Muy buen producto... pero no es de 30AVoltage to the servo will not change with the screw adjustment. It's stay the same as the default voltage 5.2 V.I have it installed in my Raven, this thing works as advertised, the Opto Kill swiitch works really well. Just one little quirk, regardless of the servo direction you put the Opto Kill Switch onto, it defaults to the off position. Meaning, if you turn on the receiver regardless on the position of the switch on the transmitter, it defaults to off. Other than that little quirk, it's a great little unit. I have 2 X 2400 Mah 20C Lipo's hooked up to it, and the voltage regulator set to 6.0 volts. To adjust this, you'll need to turn in the potentiometer about 2.5 turns inwards. But the voltage is stable regardless of the state of the 3S Lipo. Receiver voltage is stable at 5:0Volts. Highly recommended.
Note, this is a rebranded RCCSKJ Power distribution board. The Yellow one is rated at 20 amps with peak of 30, that's a whole lot of amps for any size plane.
Diode Schematic bt JohnnyB download now [12kb] Schematic by JohnnyB download now [12kb] Instructions download now [107kb] Exploded download now [1096kb] Plastic....... download now [95kb] schematic design download now [2788kb]