MultiStar ESCs are are a quality speed controller at a fantastic price! Designed for simple installation and easy setup these ESCs have proven to offer excellent performance when used in Multi-rotor applications. If your starting out in Multi-rotors and need an easy to install solution that is tested and proven to work with Multi-rotor craft then these speed controllers have you covered.
These ESC's features a very smooth yet linear throttle response, without sacrificing a rapid, crisp, response to any throttle input. Safety is not forgotten with all Multistar Esc's featuring adjustable battery LVC (set battery type to LiXX to disable LVC), stalled motor (overload) protection, signal loss shut-down and safe arming.
All Multistar series ESC's come with bullet connectors installed that are suited to the ESC's rated power handling. This allows for plug and play convenience by simply adding the appropriate battery supply splitter (3,4 or 6 ESC) and motor lead extensions from the Multistar modular accessory line. What could be simpler?
All Multistar ESC's feature an ATmega MCU that opens the door to customizable firmware - for those so inclined! or alternatively a programming card can be used with the installed software for quick and easy setup with the pre-flashed software.
Please refer to the related items below for a solder free multi-rotor power solution to suit your next multi-rotor project.
• Smooth and linear throttle control
• Fast response to throttle input
• Atmel MCU
• Stalled motor protection
• Throttle signal lose protection
• Safe power-on (throttle lockout)
• Support 480Hz+ high refresh rates (up to 499hz)
• Compatible with programming card
Constant Current: 30A
Input Voltage: 2-4 cells Lipoly
BEC: None (OPTO)
PWM: 8 KHz
Max RPM: 240,000rpm for 2 Poles Brushless Motor
PCB Size: 41mm x 24mm
Discharge Plugs: Male 3.5mm Bullet Connector
Motor Plugs: Female 3.5mm Bullet Connector
Hmotnost ( g )
ESCs are OK!
They heat-up a bit at 15Amps, a bit jumpy at start but ok in overall. You just can't beat the price.
Their cooling can be improved greatly if the wrapping is taken off (carefully, don't short-out anything on them!) and the heat spreader is exposed directly to airflow or propwash.
Even better, stick them spreader-side on the booms if they are square aluminum type. (zip ties, some thermal grease, you know.. ) Everybody put's their ESCs with the heat spreader facing outwards even if they have metallic booms that could take the heat away fast.I use them in a 2.1Kg Quad. They work but 30A is quite overstated. You guys should write realistic numbers on your stuff.
Hovering current per ESC is 5-7A (Measured with accurate industrial clamp meter) and flying current up to 17A so they should handle is with ease but two of them get really hot.
No matter to which motor I hook them up, it's always the same two that get hot...
I really can't imagine this ESC to work at currents above 20A.
Ordered TurnigyPlush now.A great ESC, i have these on 2 of my multi-rotors and am very happy with them, they do not get too hot and are very smoothThese ESCs are rated for 30Amps.... but it cannot handle more than 6 Amps.. all four of them over heads and shuts down randomly in 4 to 5 minutes of flying.. my quad crashed 3 times due this problem and third time into pieces... these escs are crap.. never again buy these ones....Decent ESC... You likely want the programming cards as well though, since you can't configure much without it.
If you want ESCs for a multirotor, you are likely better off with AfroESC than with these. They might make a nice low cost option if you are willing to flash them yourself though... (The 40A ones have an all-NFET design, which should have better performance though)
I haven't flashed mine yet, stock firmware is OK...no need simonK firmware i think. it's very good with stock firmware but it needs little bit programming. on some frames (X650F) it doesn't fit esc mount and cables are too shortbought multistar esc for use with multirotor obviously. wondering if the f-20a/f-30a might be a better choice for the FETs, but currently these are pretty good. going to flash them with simonk.Good ESC but not great, I tried them in a quad that I have SimonK controllers with a KK2 board and it took a lot of adjusting but didn't fly as well, but was better than a regular ESC.
These OPTO units don't seem to like being flashed with SimonK firmware, I flashed mine with the KDA file and smoke started coming out of my test motor, though I've seen people succeed with the BEC version, I may have had a dud but wasn't willing to try anymore.
i guess it is ok to use it as it is, but don't try to flash it with simonk firmware because they won't work smoothly. jerky movements and not reliable when flashed.alle 4 gelieferten Regler nicht in Ordnung gewesen! Gleiche bei einem Kollegen. Hoffe das war nur eine schlechte Serie und es wird behoben.
Turnigy Multistar ESC User Manual download now [2384kb] ESC-bad download now [165kb] opto board2 download now [346kb] board_a download now [244kb] board_b download now [235kb]