The Wing Wing Z-84 is big fun in a small package! With its low price and ultra-tough EPO foam construction, the Wing Wing offers excellent value and fun at a price you can't beat!
Simplicity and practicality were kept in mind when designing this airframe. It offers an easily removable magnetic battery hatch, plug-in wing and tail design, carbon fiber wing spar and molded cooling holes for the battery compartment.
Most importantly, the Wing Wing flies as good as it looks. This model features a very wide flight envelope - it's equally happy zipping along at full throttle as it is gliding with the power off. It's also very aerobatic allowing for tight loops, fast rolls and just about any other wing aerobatics you choose to throw at it.
This version of the Wing Wing arrives in kit form, so you will need to add your own motor/ESC, servos, 4 channel transmitter/receiver and batteries. Simply glue on the wings & vertical stabs, install your electronics, setup your control rods and your ready to fly!
Ultra-tough EPO foam construction
Large cooling holes for the battery compartment
Aerobatic flight capability
Flying Weight: 300g
Wing Wing airframe kit
Hook and Loop Strip (for battery mounting)
4 Channel TX/RX with elevon mixing
2900kv brushless motor
10~20A brushless ESC
2 x 9g servos
1300~1500mAh 2s Lipoly
Hmotnost ( g )
Motorsize ( průměr -or- cc)
Rozpětí ( mm ):
SaleWeight ( g )
Rám / PNF / RTF (mm)
IC / 2 : Elec:
Kapacita ( mAh ):
I bought this as my first airplane, i only fly fpv racing quadcopter so I can use this as a fpv plane. It is hard to master, I only used a couple of batteries flying in counter clockwise circle LOS, but it is fun. You need to stick with it, I crashed a LOT :D
Dont fly in windy conditions :) and mine came WITHOUT GLUE ( so only 4 crowns), so i used 6min epoxy, what a mistake becouse it doesnt stick good, than used hobyking superglue medium ca and it is ok.received in good condition, don't have time to assemble yettough plane, I crashed landing this multiple of times and its still in one piece. there is a problem in the motor mount when used with 3s 1300 and turnigy 2200kv motor, it shoots straight up as if its tail heavy, I managed to adjust the thrust angle couple of times but I'm still not getting it to fly straight when full throttle is applied. it flies great on mid throttle and hold itself in the air good even with high winds. I'll update again after managing to make this fly straight on full throttle. I'm trying mixing some elevator down when full throttle to compensate for the pitching of the nose. I suspect its more of a 2s setup with big prop but I'll keep trying till I get it right. I have another new kit that I'll paint and build after figuring out the right formula on this frame. not a bigger plane except if you have someone experienced to build it and test it for you first5 stars on value & quality. I've used a 2200kv D2826 motor, 3S 2200mah battery & a 30A ESC on 6045prop. Motor & ESC are soldered direct to save weight. AUW=450g & could be lighter using a miniquad motor & a smaller battery. *Getting CG correct is essential on this wing*. For 35$ this is a great pocket-rocket ship that flies like a bigger aircraft than it really is on low-rates.This is my second unit, first one lasted about a year and has been repaired and still flys- sort of....but they are such a great little wing I had to get another.
Easy to set up and launch and very capable of slow flight or simply amp it up, but i will reinforce the carbon rod connection section of the wings this time.
overall a great wing and worth the dollars.Great little wing!
My setup is Turnigy SK3 2822 1740kv motor, 1400mah 3S battery, 6x4.5 bullnose prop.
It flies really well, it's super fast on full throttle but can fly slow, too.
I've set dual rates to 60pcnt and expo to 50pcnt which makes it easy to control.
Had a few crashes - still in one piece. What may be worth doing is to put some tape or laminating film on the leading edge and the nose.The plane comes nicely packaged the parts seem very solid. It goes together very easily 15mins build time. Im using a Funfighter motor with a 5x5prop using 30 amp Esc 1600mah 30c battery. Flys nicely and very fast :)4.75 x 4.75, 30 a esc, 2600 kv motor, 1000 mh 3s, flies good, initially needed to get fair bit of weight in nose, maybe ill try a bigger battery and rearrange equipment. good wing for the price.Very very nice wing, I love it.
I'm using D2826-6 2200kv, 6x4 APC, BS40A, Turnigy TGY-50090M
I'll love it on 3S with 2.2Ah batteries
It's funny on 4s (tried it with 1.3A and 2.2A) but it need reinforcing or laminating.
Just received this model today, and first impressions are great!! Looks fast and aggressive, but I can imagine it sloping really well with a low weight setup! Looking forward to putting it together and maidening it!!
WingWing download now [531kb] my wing wing z-84 ready for flight download now [149kb] No File Name download now [1819kb] No File Name download now [1744kb] No File Name download now [1909kb] No File Name download now [1507kb] No File Name download now [1617kb] No File Name download now [1617kb] No File Name download now [1274kb] No File Name download now [1169kb] Roo power download now [1662kb] Roo power download now [979kb] paint issue download now [3.01Mb]