The Z700-V2 is a Super-sized and well thought out 700mm quad frame built from quality materials. The main frame is glass fiber while the arms are constructed from ultra-durable polyamide nylon.
Assembly is a breeze with pre-threaded brass sleeves for all of the frame bolts, so no lock-nuts are required. A great feature of this frame is the large mounting tabs at the front and rear of the main frame bottom plate for mounting cameras or other accessories. This makes for a great way to take aerial video or fly FPV without the need to add any additional mounting brackets.
The Z700 also features colored arms (2 white and 2 red) which are great for orientation. It helps to keep you flying the right direction without the need for different colored props.
The Z700 includes a hi-leg crab style landing gear set and a hook and rod mounting support. We offer a full line of multi-rotor electronics such as multi-rotor control board, ESC & motors. It has never been easier or more affordable to get a quad in the air!
• Built from quality glass fiber and polyamide nylon.
• Pre-threaded brass sleeves for all of the frame bolts.
• Colored arms for orientation to keep you flying in the right direction.
• Hi-leg Crab style landing gear
• Hook and rod Mounting options
• Large mounting tabs on the main frame bottom plate for easy camera mounting.
• Easy assembly.
Height: 58mm w/o crab gear 258mm with crab gear
Weight: 570g (w/ included Crab hi-lift gear)
Motor Mount Bolt Holes: 16/19mm
Hook Rod Rail: 55-60mm center to center 12mm rod (11.75mm)
Kapacita ( mAh )
Hmotnost ( g )
First off, as quadcopter frames go and as the title suggests, this frame is enormous. For that reason, I have given this frame a slightly better score than I should have since it does come with a few errors. The brass sleeves for the screws are slightly covered by plastic and you have to spend a bit of time removing it. The motor mounting holes are irregular and you may need a few extra screws and some adapters to attach your motors. This aside however, I was surprised that my 2kg quad didn't buckle at the arm joints and fall to the ground in spectacular fashion. In fact, it flew almost perfectly first flight with an ardupilot controller. This frame is perfect if you're aiming to build for cinematography, photography (since the included crab legs are a plus) and if you just want to fly a huge quad. Good luck!Just as others have stated the arms are to flexible. I was having problems with stability and the quad wanting to twist to the right no matter what I did. I ordered the Upswept Upgrade Arms for DJI Flamewheel Style Multirotors V500 / H550 (Blue) (2pcs), installed them and all my problems disapeared so if you want wide center frame plates you can buy this but count on doing something to apgrade the weak flexible armsgran i facil de veure a l'aire. espai de sobres per ficar una apm 2.6 amb tota la trasteria. osd, gps etc. fora estable i facil de monta. els braos flexan bastant pero en vol va fora be.
motors 2830 amb pala 9x4, variadors de 40amp i bateries 3s 5200mha. un dron mes que funcionaThere's been a lot of complaints about the flexible arms, and I have a solution. Lightly sand the outer sides so epoxy will adhere, then epoxy carbon fiber strips on both sides of the arms. This will stiffen the arms enough to allow for stable flight. SteveThe arms flex way too much. Lots of vibration. The center section is fine, lots of room, good construction. Stiffen up the arms and it will be fine.Does not fly well at all. Excessive arm flex creates huge instability problems. Unsuitable for fun flying to say nothing of using it for a video platform. FORGET this platform and look for something else.OK I wanted to go bigger than my F450 Quad so I decided to give this a try even though a few people have said there was too much arm flex. Anyway after putting it all together the first flight was smooth but Quad rotated right and needed left rudder to correct. I went through the quad again after posting for help in a few places and 1 arm may have been twisted enough to cause the problem because after slightly bending it after heating it and letting it cool down may have fixed it ( also went through my KK2.1.5 again and verified everything again it fly perfectly. Yes the arms have flex but I can deal with it. The landing gear could be better & I may swap it out or add to it to strengthen them maybe even add a battery holder to each side some how. I am using some cheap 800kv motors with 12.4.5 props to start with as I'm a novice then go to carbon fiber ones eventually. I am also running a EMAX 25amp 4in1 ESC in the quad as well as my F450 without issue. I have set this up for FPV and have Built my own Ground station and will post some videos of it soon.This frame is not rigid and it vibrate with low KV motor and big propeller. In my case I have try it with 12 prop. Too much vibrations! The arms distords.For me, It wont fly properly, the arm flex to much creating an unstable craft, it look like the KK2 is always figthing no mater what setting, same goes for the Naze32. I have swap everything to confirm my stating, motor, ESC and board. I have tried everything else. the only way to resolve that where to install smaller and stronger (450) arm. My 3 stars goes to the frame.The arms are very weak and flexible. It can not even hold motors. When used with landing skid, arms become curved because of the motor weight. In addition, during flight, it sometimes shakes because of flexible arms. May be good with 22/28 size 0945 size props, where the shaking force is low.
Instead of this frame, you may choose another Hobbyking product; whose arms seem more rigid: http://www.hobbyking.com/hobbyking/store/__56209__Q680_V3_Glass_Fiber_Quadcopter_Frame_680mm_Integrated_PCB_Version.html