Neue Produkte Forum
Registrieren

Total Price

0,00 €

Warenkorb 0 Warenkorb 0 Loading...

CNC-Alu-Gas Arm für Gasmotoren

CNC-Alu-Gas Arm für Gasmotoren

Shipped From:
  • Global

Now save Speichern 0,00 € 0,00 €

5,31 €
Alert me
Status:
Ausverkauft!
SKU:
017000180-0
WANT FREE SHIPPING? Click here to find out more!

CNC-Alu-Gas Arm für Gasmotoren - 2mm Gewindebohrung für pushrod Kugel Link / Gabelkopf.

  • Artikelbezeichnung 017000180-0
  • Brand Other
  • Kapazität ( mAh) -
  • Gewicht 17.0000
  • Länge 60.00
  • Breite 9.00
  • Höhe 45.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Muy util y barato....

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Muy util y barato....

I have used several of these on Walbro carbs to solve a common problem involving clearance and positioning of the throttle arm on my gas powered planes. Perfect fit with extended housing and arm make life hooking up the throttle much easier. I recommend them.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I have used several of these on Walbro carbs to solve a common problem involving clearance and positioning of the throttle arm on my gas powered planes. Perfect fit with extended housing and arm make life hooking up the throttle much easier. I recommend them.

Perfect. These arms work great with almost ANY Walboro carbed engine.



Remove the existing screw, pry off the old short arm, and insert this one. Tighten down the berg screw and you're done.



You can install a ball socket screw for a freely moving throttle linkage setup.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Perfect. These arms work great with almost ANY Walboro carbed engine.



Remove the existing screw, pry off the old short arm, and insert this one. Tighten down the berg screw and you're done.



You can install a ball socket screw for a freely moving throttle linkage setup.

Very impressed with arm, appears chrome plated, very attractive. Fits on my RCG26 and DLE30 easily. Specs are as follows: ID is abt 4.8mm as fits throttle shaft of 4.75mm snugly, OD is 9.5mm/.375", overall HT is 18.5mm/.731", Center shaft to 2mm linkage hole is 17.35mm/.731", overall width is 25.1mm/.99". Uses a 3mX3m set screw requiring a 1.5mm hex driver. These measurements are as accurate as I could obtain using electronic caliper. I will order additional arms for other engines. Hope this helps those needing dimensions. Would work on chokes with same diameter shafts.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very impressed with arm, appears chrome plated, very attractive. Fits on my RCG26 and DLE30 easily. Specs are as follows: ID is abt 4.8mm as fits throttle shaft of 4.75mm snugly, OD is 9.5mm/.375", overall HT is 18.5mm/.731", Center shaft to 2mm linkage hole is 17.35mm/.731", overall width is 25.1mm/.99". Uses a 3mX3m set screw requiring a 1.5mm hex driver. These measurements are as accurate as I could obtain using electronic caliper. I will order additional arms for other engines. Hope this helps those needing dimensions. Would work on chokes with same diameter shafts.

Very good arm for gas engines.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very good arm for gas engines.

Excellent solution to an often overlooked problem. Fits, works and alieviates problems with the choke rod fouling the throttle rod

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Excellent solution to an often overlooked problem. Fits, works and alieviates problems with the choke rod fouling the throttle rod

fiyatna gre ok kaliteli bir rn...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

fiyatna gre ok kaliteli bir rn...

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!