Neue Produkte Forum
Registrieren

Total Price

0,00 €

Warenkorb 0 Warenkorb 0 Loading...

D922MG Digitale Metal Gear Servo 1.8kg / 12g / 0.07sec

D922MG Digitale Metal Gear Servo 1.8kg / 12g / 0.07sec

Discontinued Product

Please continue searching for a similar product.
SKU:
D922MG
WANT FREE SHIPPING? Click here to find out more!
Speziell für Hubschrauber und schnelle Reaktions applications.Steel Material in Abtriebszahnrad für eine bessere Intensität verwendet und Ausgabeabweichung nach langer Zeit use.It hohe Qualität Motor ermöglicht mehr auf hoher Geschwindigkeit laufen zu reduzieren. Kompatibel mit vielen Kreiseln wie Futaba 401.601.
Modell: D922MG
Betriebsspannung: 4.5V / 6.0V
Betriebsstrom: 50mA / 180mA
Ruhestrom: 5 mA
Blockierter Rotorstrom: 600mA
Betriebsgeschwindigkeit: 0.09sec.60º / 0.07sec.60º
Stall Drehmoment: 1.6kg.cm / 1.8kg.cm
Größe: 22.5x11.5x24.6mm
Gewicht: 12g
Totband: ≤3uSec
Getriebe: Metall
Stecker Draht: 210mm
Betriebstemperaturbereich: -20 ° C bis + 60 ° C
  • Artikelbezeichnung D922MG
  • Brand -
  • Gewicht 23.0000
  • Länge 45.00
  • Packaging Width 45.00
  • Höhe 45.00
  • Drehmoment ( kg) (min. 0,01 kg ) 1.80
  • Speed ​​( Sec / 60deg ) 0.07
  • A ( mm) 31.00
  • B (mm) 22.00
  • C ( mm) 28.00
  • D ( mm) 11.00
  • E ( mm) 32.00
  • F ( mm) 19.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Amazing finally installed a servo on the tail of hk 250 that works, I was about to send to the trash hely

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Amazing finally installed a servo on the tail of hk 250 that works, I was about to send to the trash hely

For the price my absolute favourite! only issue is the bad soldering!! put evidentially some hot.glue at intern wiring and then you are safe. totally compares to 264mg savox!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

For the price my absolute favourite! only issue is the bad soldering!! put evidentially some hot.glue at intern wiring and then you are safe. totally compares to 264mg savox!

I guess you need to give a good rating to have your review posted, anyways I tested the servo speed and it is .15 at 5v not even close to specs. I then ran the servo continuous and about a minute in it started cycling erratically, maybe I got a dud as it has good reviews but mine went in the trash and I won't be buying them again

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I guess you need to give a good rating to have your review posted, anyways I tested the servo speed and it is .15 at 5v not even close to specs. I then ran the servo continuous and about a minute in it started cycling erratically, maybe I got a dud as it has good reviews but mine went in the trash and I won't be buying them again

I bought three of these to replace my 933's on a 450 Pro, after two were damaged in a crash.

The 933's were pretty good servos - smooth running with good centring, very little backlash in the gears and a perfect fit in the 450 Pro. On the downside, they seem to have fragile cases. I'd recommend using the HK servo arms, which are thin and quite flexible, and might offer some protection to the servo in a crash. You can use a back nut on the ball link bolt.

The main reason I decided to try the 922's was that the 933's were a bit slow - showing only 0.13s @ 5.9v on a servo tester.

I was therefore shocked to see the 922's show almost the same speed in the servo tester - 0.125s @ 5.9v.

Not only that, they also sound really harsh and rough, and have far more backlash in the gears than the 933's. I find it hard to believe they come from the same supplier.

In flight, on my 450 FBL, I had to reduce cyclic gains by 10 points from the value I'd used with the 933's, otherwise I would get a severe cyclic shake.

I also made the mistake of only ordering 3 servos - and the one I installed in the right aileron position oscillated around centre. After about 20 flights, it decided to shift it's neutral by about 30 degrees.

Overall, therefore, I think the 922's are nothing like as good as the 933's. I've since replaced them with Corona DS-929MG's. Although the Coronas have slighly more gear

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought three of these to replace my 933's on a 450 Pro, after two were damaged in a crash.

The 933's were pretty good servos - smooth running with good centring, very little backlash in the gears and a perfect fit in the 450 Pro. On the downside, they seem to have fragile cases. I'd recommend using the HK servo arms, which are thin and quite flexible, and might offer some protection to the servo in a crash. You can use a back nut on the ball link bolt.

The main reason I decided to try the 922's was that the 933's were a bit slow - showing only 0.13s @ 5.9v on a servo tester.

I was therefore shocked to see the 922's show almost the same speed in the servo tester - 0.125s @ 5.9v.

Not only that, they also sound really harsh and rough, and have far more backlash in the gears than the 933's. I find it hard to believe they come from the same supplier.

In flight, on my 450 FBL, I had to reduce cyclic gains by 10 points from the value I'd used with the 933's, otherwise I would get a severe cyclic shake.

I also made the mistake of only ordering 3 servos - and the one I installed in the right aileron position oscillated around centre. After about 20 flights, it decided to shift it's neutral by about 30 degrees.

Overall, therefore, I think the 922's are nothing like as good as the 933's. I've since replaced them with Corona DS-929MG's. Although the Coronas have slighly more gear

I tested the servo and found it to be .15 on 5v nowhere near the stated speed, followed by running it continuous and it lasted about a minute before it started cycling erratically. Not worth sending back so it's in the trash.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I tested the servo and found it to be .15 on 5v nowhere near the stated speed, followed by running it continuous and it lasted about a minute before it started cycling erratically. Not worth sending back so it's in the trash.

Ottimo servo, robusto e preciso, l'ho utilizzato per gli alettoni del mio Funcub Multiplex, dopo un forte crash in picchiata i servi non hanno subito alcun danno e fanno ancora un'ottimo lavoro :-)

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Ottimo servo, robusto e preciso, l'ho utilizzato per gli alettoni del mio Funcub Multiplex, dopo un forte crash in picchiata i servi non hanno subito alcun danno e fanno ancora un'ottimo lavoro :-)

Buon servo per il ciclico.

veloce e preciso e poi costa veramente poco.

Mi sa che ne compro ancora

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Buon servo per il ciclico.

veloce e preciso e poi costa veramente poco.

Mi sa che ne compro ancora

There have been many discussions about this servo on major web forums. Mostly, people don't read the specs that this is not .09/sec at 5V and only .07 at 6V. Theory aside, this is an awesome cyclic servo for a 450 class as it has a smooth and precise movement. It is "OK" as a tail servo on a 250, but a faster servo would be better. Overall, great value and great servo.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

There have been many discussions about this servo on major web forums. Mostly, people don't read the specs that this is not .09/sec at 5V and only .07 at 6V. Theory aside, this is an awesome cyclic servo for a 450 class as it has a smooth and precise movement. It is "OK" as a tail servo on a 250, but a faster servo would be better. Overall, great value and great servo.

it is fast servo and powerful but not as torque of DM 933

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

it is fast servo and powerful but not as torque of DM 933

tima qualidade, uso em um HK 450, apesar de no fazer vos 3D ainda, para hovers perfeito. Segundo outros colegas, pode fazer 3D com estes, sem problemas.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

tima qualidade, uso em um HK 450, apesar de no fazer vos 3D ainda, para hovers perfeito. Segundo outros colegas, pode fazer 3D com estes, sem problemas.

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save