Neue Produkte Forum
Registrieren

Total Price

0,00 €

Warenkorb 0 Warenkorb 0 Loading...

EDF Impeller 7 Blade-3inch

EDF Impeller 7 Blade-3inch

Discontinued Product

Please continue searching for a similar product.
SKU:
OR003-00109-7B
WANT FREE SHIPPING? Click here to find out more!

EDF Impeller 7 Blade-3inch
Blade - Durchmesser: 3 Zoll / 77mm
Äußere Gehäuse - Durchmesser: 83mm
Wandstärke: 1,9 mm
EDF Länge: 86 mm
Klingentyp: 7
Schachtgröße: 3,175 mm
Dieser EDF wird ein Motor mit einem maximalen Durchmesser von 31mm nehmen

Hergestellt aus hochfestem verstärktem Kunststoff.
Ersatzpropeller zur Verfügung.

Recomended Motor: 28-35 8 Turn (11.1 ~ 18.5v)
ESC: 35A
Rpm: 3,900kv
Leistung: 500 ~ 2000g Thrust


  • Artikelbezeichnung OR003-00109-7B
  • Brand -
  • Kapazität ( mAh) -
  • Gewicht 80.0000
  • Länge 95.00
  • Packaging Width 90.00
  • Höhe 90.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Used this with the Turnigy 2836 3200kv motor and 3S.
The sound is really nice actually, more "jet" than "woosh". It didn't need balancing though the motor mount seems a little weak and probably need reinforcement.
About the motor-edf combination: It pulls about 65 amps and give about 6-700 g of thrust in bench, slightly lower mounted in my machine due to the smaller outlet. The motor tends to overheat, so a lower kv motor with 4S might be a good idea.
I said "used" because I crashed my plane at 150 km/h which made the probably very hot motor to push itself through the mounting holes (again, the motor mount is a bit fragile).
All and all, I really enjoyed this EDF, but I should have choosed a lower kv motor with 4S instead of 3S.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Used this with the Turnigy 2836 3200kv motor and 3S.
The sound is really nice actually, more "jet" than "woosh". It didn't need balancing though the motor mount seems a little weak and probably need reinforcement.
About the motor-edf combination: It pulls about 65 amps and give about 6-700 g of thrust in bench, slightly lower mounted in my machine due to the smaller outlet. The motor tends to overheat, so a lower kv motor with 4S might be a good idea.
I said "used" because I crashed my plane at 150 km/h which made the probably very hot motor to push itself through the mounting holes (again, the motor mount is a bit fragile).
All and all, I really enjoyed this EDF, but I should have choosed a lower kv motor with 4S instead of 3S.

I put value only two crowns , just because it comes with 3,17mm shaft .And the fact that the mini motor for this fan they all have 4mm shaft ,Which means you got buy extra shaft for cost of $5.99 .doesnt add up . Other wise great fan . PS i dont want to open the hole to 4mm not advise able .

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I put value only two crowns , just because it comes with 3,17mm shaft .And the fact that the mini motor for this fan they all have 4mm shaft ,Which means you got buy extra shaft for cost of $5.99 .doesnt add up . Other wise great fan . PS i dont want to open the hole to 4mm not advise able .

this fan,1500kv outrunner,6 cell,40a mystery speedy,tested gives 1050grams thrust at 24.5amps..550watts....850g thrust in my kyosho f16 with restricted ducting for high speed, No cheat holes.very fast.. plane weighs 900g

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

this fan,1500kv outrunner,6 cell,40a mystery speedy,tested gives 1050grams thrust at 24.5amps..550watts....850g thrust in my kyosho f16 with restricted ducting for high speed, No cheat holes.very fast.. plane weighs 900g

This EDF motor setup is solid.. I recommend getting this to upgrade all you Jets that require more thrust for your amps..

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This EDF motor setup is solid.. I recommend getting this to upgrade all you Jets that require more thrust for your amps..

it is great edf very high quality and low price....

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

it is great edf very high quality and low price....

To get most out of fan you most close down the shroud rotor gap using duct tape or balsa wood. The gap allows to much air to pass buy making too much turbulence and you must put some foam lip or something in the inlet especially at high kv speeds.

55oz of thrust on 3s\2200\40c\88amps, 4100kv cyclone motor

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

To get most out of fan you most close down the shroud rotor gap using duct tape or balsa wood. The gap allows to much air to pass buy making too much turbulence and you must put some foam lip or something in the inlet especially at high kv speeds.

55oz of thrust on 3s\2200\40c\88amps, 4100kv cyclone motor

This EDF is awesome! I put this baby on a Hobbico Diablo and replaced the stock 55mm EDF. I made a custom underbelly mounting and tube using a 2 Liter pop bottle,so the odd size of this fan didn't matter much.I used a 2845 HXT 2200 kv motor on 4s 40c 2200 mAh Turnigy.It gives good thrust with the aggressive blades.I'm trying a 55 batt,but not sure if the motor will get too hot.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This EDF is awesome! I put this baby on a Hobbico Diablo and replaced the stock 55mm EDF. I made a custom underbelly mounting and tube using a 2 Liter pop bottle,so the odd size of this fan didn't matter much.I used a 2845 HXT 2200 kv motor on 4s 40c 2200 mAh Turnigy.It gives good thrust with the aggressive blades.I'm trying a 55 batt,but not sure if the motor will get too hot.

comprei para o motor Wild Beast FED Outrunner 4880kv de 70 milmetros com variador 90 / 100 hobbyking ss

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

comprei para o motor Wild Beast FED Outrunner 4880kv de 70 milmetros com variador 90 / 100 hobbyking ss

Great fan unit super strong, it just doesn't fit any regular Jets, this brand and size fit well for 90mm and not an upgrade for 70mm too much foam removeal

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great fan unit super strong, it just doesn't fit any regular Jets, this brand and size fit well for 90mm and not an upgrade for 70mm too much foam removeal

Could be a bit more harder the plastic, when it reach critical rpm the blade touched inside walls(

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Could be a bit more harder the plastic, when it reach critical rpm the blade touched inside walls(

  1. 1
  2. 2
  3. 3
  4. 4
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!