Gesamtpreis

0,00 €

Warenkorb 0 Warenkorb 0 Loading...

EDF55 Impeller-Gehäuse für 55mm-System

Generating Links

EDF55 Impeller-Gehäuse für 55mm-System

Preis:

Now save speichern 0,00 € 0,00 €

2,81 €
Menge:
Versendet aus:
  • Global
Bereits gekauft
Status:
Auf Lager
SKU:
EDF55-DHS
Kostenloser Versand? Klicke hier um mehr zu lernen!
EDF55 Impeller-Gehäuse für 55mm-System
* Nur Fall.
Video hochladen

Registrieren Sie sich bitte, um Videos hochzuladen anmelden oder Registrieren

Themen
Sortieren nach
Neueste Themen
* Nickname:

* Deine Antwort:


Geben Sie den im Bild gezeigten Text in das Feld unten ein
*Verifizierungs-Schlüssel:
Abbrechen
Senden
Poste ein neues Thema
* Nickname:

* Dein Thema:



Geben Sie den im Bild gezeigten Text in das Feld unten ein
*Verifizierungs-Schlüssel:
Beitragsthema

Registrieren Sie sich bitte, um Bewertungen zu schreiben anmelden oder registrieren

eldiablo155 | Verifizierter Käufer

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Dec 30, 2014

good product with some reinforcement , the bad side is : this thing should work with small engines , and where the engine should be anchored by screws the plastic layer is too much, it would be perfect if it was less ticker

Ral fRotten | Verifizierter Käufer

  • Quality
  • Value
  • Overall

Certified Buyer Rated

May 22, 2014

The fan blades for this need to be 55mm, the actual housing is 58mm, and the rolled edge of the intake lip is 70mm outside diameter, there are 3legs on it and not 4 as shown in the picture, 1 leg is hollow for the motor wires, I intended to use it as a motor mount for a pusher but the 58mm is too wide, so back to the drawing board for me.

Grazy | Verifizierter Käufer

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Sep 29, 2012

4 stars just for safety. Received 2 of these and one had a few imperfections, but could easly be fixed with an exacto knife. The other one is perfect. Mine have only 3 spokes. I like the one hollow spoke. The three motor wires fit tight, but neatly through. Out of the way and it look much better than open wires. Have not run it, but I foresee no problem. Well made.

EODPete | Verifizierter Käufer

  • Quality
  • Value
  • Overall

Customer Rated

Sep 12, 2012

Really thick hard plastic. Seems stronger then the fan unit it is replacing. Mine is differnt then the one pictured, mine only has two mounting points. The mounting tab is really thick and I need to find longer screws to mount my EDF.

__bare | Verifizierter Käufer

  • Quality
  • Value
  • Overall

Customer Rated

Jul 15, 2012

This is an OLD and obsolete version fan housing.
Current versions a have a tube for motor wire exit.
Caveat Emptor

benw | Verifizierter Käufer

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Apr 19, 2011

Good EDF housing. No need to worry about the exiting wires from the motor with this EDF Housing. I prefre these units. With the GWS units I have, I had to cut holes to allow for the exiting wires of motor.

smasher41 | Verifizierter Käufer

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Jun 27, 2010

Odd fan unit but works with motors that dont ahve a standoff, also had hole pattern than accepted larger screws than most.

seems nice and round also

Kundendateien
No File Name Download [364]
Datei hochladen

Registrieren Sie sich, um Dateien hochzuladen.
Bitte anmelden oder registrieren um jetzt Hobbyisten zu helfen!