HobbyKing® ™ Mini Saturn F3A 3D EPO Flugzeug 580mm (PNF)

• Overall
• Quality
• Value

Crash resistant

Apr 13, 2018

I have put 20 flight's on the Mini Saturn & crashed it twice badly. It has survived both crashes very very well, no servos have jammed. The supplied servo's seem to do the job well, for now. Foam is crash resistant & glue's up well to. Awesome little pattern flyer. Very nimble & can handle the wind well, surprisingly considering no gyro. The rudder's pull pull cable (kevler) hasn't stretched much at all, adjusted after 10 flight's now it's not stretching anymore.

• Overall
• Quality
• Value

Good flyer

Mar 01, 2018

I’m flying mine with a futaba micro fasst receiver and a 2s 300 mah pack. Perfect for backyard practice

• Overall
• Quality
• Value

Good little pattern flyer.

Feb 18, 2018

I bought this to replace my eflight umx Beast & i'm glad i did. The build was straightforward & good instructions manual. The servos are not the best of quality but they do the job well, don't think they will handle bad crashes tho. Prop hanging requires a lot of stick work to keep it stable but that's the nature of the plane. It's a great pattern flying plane. Happy with the purchase.

• Overall
• Quality
• Value

Menz989

Aug 01, 2017

This thing is an absolute weapon. Love it

• Overall
• Quality
• Value

2.5 gram servos

Mar 13, 2017

servo's are junk, jitter to much, will not center correctly. On the push they work good, on the pull they stutter and take to long to move to full position. all 3 act the same. no stickers to tell what servos these are. will need to purchase other servos elsewhere.

• Overall
• Quality
• Value

Nach dem Testflug

Nov 29, 2016

- Die Bauqualität der PNP ist gut, Servos waren in Mittelstellung, Motor war gut montiert
- Das Dekor am Rumpf ist sehr dünn und zeigt Ablösungserscheinungen - nichts wildes
- Die Seitenruderanlenkung wurde durch 1mm Draht ersetzt wie beim Höhenruder, die 2 Bindfäden sind sonst sehr Bastelig
- Die Propelleraufnahme wurde durch einen Propsaver mit O - Ring ersetzt, da sonst die Welle schnell Schaden nimmt
- Fahrwerk bisher noch nicht montiert, da viele von Bruch schreiben


Hatte am Samstag Testflug,

- Ausschläge sind ca. 50% von den empfohlener für den Anfang mit 40% Expo, steigern kann man das immer
- mit dem Serienpropeller zuwenig Schub! Sogar mit Vollgas war er kurz vor dem abschmieren trotz neuer Akkus
- Auf 7035 Propeller umgerüstet, jetzt kann man damit torquen, ich habe nur Bedenken wegen des sehr kleinen Motors und Reglers ob etwas überlastet wird - Gibt 1 Punkt Abzug
- Für die Halle tauglich, dreht schön auf dem Teller und wird nicht zu schnell, kippt nicht in der Kurve
- Fliegen sollte man können
- Es passen nur micro empfänger (indoor Empfänger). Wegen der abnehmbaren Haube ist auch schwer Platz zu improvisieren. Ebenso passen kaum andere Akkus. Mein 2s 450mA passt quer und der Schwerpunkt stimmt auch.
- Flugzeit 6min mit 300mA Verbrauch langsam geflogen
- Für draußen nur bei kein bis wenig Wind empfehlenswert und zum einfliegen!
Gruß
Volker

• Overall
• Quality
• Value

Customer Rated

Sep 13, 2016

This is a cheaply designed plane. If you are new to the hobby be ready to make many repairs. Motor mounted with 4 ear tabs but nothing to back up the motor. Ears break easily. I had to create my own motor mount after several prop strikes. The aileron linkage is of very thin plastic mine broke. Had to cut a couple servo arms I had and cut/glue them into the aileron. Just know this, while the manual shows replacement parts, there are no replacement parts.

• Overall
• Quality
• Value

Certified Buyer Rated

Mar 04, 2016

Easy and fun build. The plane flies nicely however you need to have good experience in flying, i.e. not for beginners. The landing gear is a bit too week and mine broke on the first hard landing.

• Overall
• Quality
• Value

Customer Rated

Mar 01, 2016

The use of CF rods forming I section structures makes the model very strong and rigid as well as very light. The battery slot is designed for the Nanotech 300mAh battery. The hatch section receptacle base for the receiver has a U section which fits the curved section of HK's micro stabiliser receiver perfectly! My only real complaint about lack of thought or integration is the use of the Futaba connectors for the servo leads. These are far too lumpy for plane which uses micro everything. The said receiver uses micro JST 1.25mm 3-pin connectors. I'm in the throes of getting micro JSTs to replace the Futabas.
I like the moulded plastic nose cowling. The motor has a shaft which matches the GWS prop fastened with the spinner shaped nut. This creates a smart streamline shape!

• Overall
• Quality
• Value

Customer Rated

Mar 01, 2016

Although I haven't flown mine yet I must say I really like the design of this model. The demo video by Michael Wargo shows the plane to be a very nice 3D model. It has picked up on many object lessons and much experience in retailing model aircraft by HK over the years. It gets lots of the bits and pieces together and integrates them in a way which bothered HK products many years ago when I started being a customer.
Others have criticised the quality of the servos which I guess I shall see. I have a couple of their Blue Arrow 2.8g servos spare to slot in. More in another posting...