KD 600XL 1100kv Brushless heli Kundschafterschulterstücke / 1600W

• Overall
• Quality
• Value

Customer Rated

Jun 16, 2013

I bought this motor for my scale CH53 helicopter. When starting it for the first time the engine blocks suddenly. Fortuantely the helicopter was on the ground. The ESC was defect too.
After unmateling the motor I saw the reason.
7 magnets were missing from production and 1 magnet was broken and blocked the motor.

The answer from HK:

Dismantled items are void from the warranty.

• Overall
• Quality
• Value

Customer Rated

May 05, 2013

Just received this two of these motors and will use in a Hirobo shuttle E-conversion. Motor came with the cooling fans attached, but the connectors and shaft collars were for a 28mm motor, so I have to come up with a shaft collar for each motor. I will report how the motors run at a later date.

• Overall
• Quality
• Value

Customer Rated

Apr 24, 2013

The magnet of the motor was damaged when raising the number of rotations of the motor.
Money has been applied vainly.

• Overall
• Quality
• Value

Customer Rated

Oct 27, 2012

Bought this product and during its first real hover it was going well until smoke started coming out the motor. HK is looking into this thx HK. This is a quite motor and has good power.

• Overall
• Quality
• Value

Customer Rated

Aug 04, 2012

I can only warn everybody to buy this product.
1. it does not have a spring on the shaft to to keep the housing with magnets to the rotor.
2. the magnets came loose after 1st flight, destroyed the motor and damaged my heli.

• Overall
• Quality
• Value

Customer Rated

Jul 08, 2012

This motor does not work,bad quality,after 5 seconds damaged,i send the motor back to HK in Hamburg,no response until now.

I dont want such parts.Ordered now the Typhoon 600 H and hope to be lucky with this.

• Overall
• Quality
• Value

Customer Rated

Jan 02, 2012

Just tried this motor in a DeNight Special 60" pylon racer. Was looking for a high KV motor for sport flying with a 6-7 lb plane, that would run on 4S voltage. Very pleased with the behavior of the motor it is smooth and quiet with a 13 x 6 inch propeller. Motor didn't heat up.
The motor pulls far more amps than the 55A in the documentation. I started to heat up a 4S battery that can put out 100A. My guess is that amps spike close to 100A.
The DeNight Spacial can fit 2 x 5,000 mAh 4S in the battery compartment, and this should provide the current that the motor likes.

• Overall
• Quality
• Value

Customer Rated

Dec 23, 2011

This motor lasted 30seconds in my Trex600 Heli. I new it was going to be be bad when I ran the motor up in the fram and mesured the vibrations with my cell phone like I do when I balance EDF units. The vibrations where off the chart. I think it would be a great motor if it was blanced better. Mine did have the fan. Maybe i should of left it off.

• Overall
• Quality
• Value

Customer Rated

Sep 12, 2011

i try mine motor for the first time today on my HK600 heli with a 6s 4000mah batterypack. i hear noise when i give some throttle and my motor just stuck. the magnets just came off and destroyd my motor. i'm very glad that my heli was on the ground when it happend. i got another motor but i'm scared to use it now.

• Overall
• Quality
• Value

Customer Rated

Jul 03, 2011

I just received another dut. I tried all possible combinations of timing, pulse modulation and pole counts with no improvement.
When the motor spins up, it starts to make a screeching sound because the magnets touch the stator. I can not even go to half throttle.
Anyone that was lucky enough to receive a working motor, what pole count, pulse modulation and timing settings did you use?
Thank you in advance.