Mini Talon FPV Flugzeug EPO 1300mm (KIT)

• Overall
• Quality
• Value

Customer Rated

Sep 18, 2015

Super avion pour du fpv cool. Avec un apm dessus et une 4s 5000. Le centrage indiqu est parfait. Le lanc et trs facile mais il faut faire attention au couple de l'hlice lors de la mise des gaz. Prvoir un renfort de la pice en bois qui touche l'atterrissage.
Mont avec un plush 40a, moteur 2217 800kv et helice apc sf 10x4.7 a suffit largement.

• Overall
• Quality
• Value

Customer Rated

Jul 09, 2015

Not a bad aircraft. Quality is pretty good and it is tough too! Loads of room inside but inconvenient access/battery placement. Need a better system to close top access door and keep it latched. I didn't use v-tail trim and it flew well as a yank and bank. Rear skid section should be redesigned as wooden skid is a weak point. Very fast with the right motor/prop/battery combination. Watch out for roll to the left when launching.

• Overall
• Quality
• Value

Customer Rated

May 15, 2015

I can't be happier with this plane.
It was easy to build, all pieces fit perfectly and are really well finished.
One nice detail is that wings can be easily detached and reliably attached using a screw that holds them in their position.
Having watched some videos, I was concerned about landing speed, but actually it does not need much space to land (watch the video).
It is very stable, and with the motor I used (dys 2217 1500kv) taking off is really easy, and it climbs really well.
The only problem I have found so far is the tail wood landing squid is too fragile, and needs reinforcing.

Here is my maiden flight video (gear list in video details):

https://www.youtube.com/watch?v=exoCKpwOr_0

• Overall
• Quality
• Value

Customer Rated

May 13, 2015

Excellent quality. Used hot glue and epoxy to put it together. Mines 1000g with gopro 3 and without battery so auw will be around 1300g. Hxt900 servos fit as good as perfectly into the slots (they could be .5mm thinner) but its not a big deal. Get some servo extension leads 2x10cm and 2x 20cm would be great

• Overall
• Quality
• Value

Customer Rated

Mar 03, 2015

I have to say, I suck it up with the high price of shipping on this FPV Plane, I will tell you right now, it was worth it,, very nice indeed, and lots of room for my gear.. very nice job indeed Hobby King, Thank you..

• Overall
• Quality
• Value

Customer Rated

Jan 30, 2015

I have Purchase This Plane with Spec Below. Got 30min Flight Time.
-ntm 2826 1000kv
-3 blade 8inch proppeller
-3500mah 11.1volt
-ArkBird FC
-Mobius Camera
-Hextronik MicroServo
-600mw Boscam 32ch VTX.

• Overall
• Quality
• Value

Customer Rated

Nov 18, 2014

I use vector OSD FC ,60HK esc SimonK flashed, 1450kv Emax motor , 4s 5000amp , very heavy but fly very smooth it can handle weight easily .

• Overall
• Quality
• Value

Customer Rated

Aug 17, 2014

I am really blown away with the quality of this kit. All parts fit perfectly, surfaces are SUPER smooth and the build is as easy as it could get with an ARF foamy. Wings are super stiff, plenty of carbon rods in there.

Only downside: The top hatch is a bit weak at the aft wing spar. Easy fix is to strengthen it with some carbon flats. Also see RCGroups or other forums on this.

Five crowns, will maiden today.

(Setup info: 2830 1000kV, 9x5 HQprop, HK 15178 servos, Plush 60A, Zippy 5000mAh 4S, AR600 for test)