NGH Engines einen wohlverdienten Ruf für Leistung und Wert gewinnen, sind sie dazu gemacht Modell Aero Engines, nicht konvertierte Kettensäge Typen. Die Weiterentwicklung von NGH macht diese einige der besten heute auf dem Markt erhältlich.
NGH weiterhin mit dieser ersten Produktionsgas 4-Takt-Motor für Innovationen, Sie alle Vorteile und Ton eines 4-Takt erhalten wird, aber mit der Wirtschaft von Gas. Dieser Motor wurde von Grund auf neu entwickelt und verfügt über eine Walbro carb, RcXEL Zündung, Doppelwalze CNC conrod, Doppel beringt Kolben für eine bessere Kompression und ist Träger oder radial mit den mitgelieferten Ständer angeflanscht. Mit seinem markanten Aussehen ist gewährleistet, Köpfe auf jedem Flugfeld einzuschalten.
• Kompakt und leicht
• Strahl oder traditionelle radiale Halterung
• Hervorragende Qualität und Leistung
Typ: Gas 4 - Takt luftgekühlter Motor
Bohrung x Hub: 39 x 31,8 mm
Verdichtungsverhältnis: 9: 1
Crank Typ: Geschmiedete mit Doppellager Unterstützung
Kurbelwelle Gewinde: 3/8 "x 24TPI
Vergaser: Walbro Benutzerdefinierte WT1022
Drehzahlbereich: 1800 - 8000rpm
Zündung: Auto voran RCEXL DC-CDI
Zündkerze: CM6 RCEXL
Zündung Leistung: 4,8 ~ 6V DC (4 ~ 5 Zellen NiMH - Akku)
Kraftstoff: Bleifreies Benzin / Öl - Gemisch 35: 1
Empf: 18x8 / 18x10 / 20x8 2 - Blatt
Gewicht: 1580g mit Zündanlage
Gewicht ( g)
Schreiben Sie Ihr eigenes ReviewSurprising value and performance for the $. Pulls a 1/4 scale Tigermoth with authority and nice four stroke sound through the straight pipe, no muffler needed. Arrived tuned and ready to run. Needed 1/8 leaner turn on the low end jet. Idles smoothly at low RPM. Transitions to full throttle instantly. I also run an OS FG40 four stroke gasser. The OS has more power, but for $450 less, I'm planning to order another NGH soon. Measure your cowl length though. With rear carb and a long crankcase this engine is longer than some others. I took 1 3/4" off of the engine box for the Tigermoth and reinforced the new firewall well with gussets and fiberglass.I bought this motor for a Piper Pa - 25 with 2580mm span . the motor runs very well and quiet.
The Price and the Quality of the Engine is also very goodBought a new one of these last summer. Had to go to Aus tars for a beam mount and Big Pla nes for a muffler. Apart from that, the thermal spacer (white washer was not flat and was causing an air leak in the inlet. After fixing that, it ran great. Is being fitted in a 1/3 scale SpaceWalker. A friend then sold me a slightly used one for 60 (Thats what I said) and also had the same problem. Quickly sorted, it flew last sunday in a Cap 232 72" span and was a great performer. Very clean, sounds right, and lasts 15min on a 16oz tank. Using a 20 x 8 prop at 6000rpmSo far so good. Only ran half a tank through it so far with 30:1 oil mix. 18x8 wooden prop.I have received this engine from hobbyking recently. It was in a perfect condition when it arrived. All additional components neatly packed in separate bags. I have read on some fora that people received their engines with damaged cooling fins, but not this one. Must point out that these engines where not supplied by HK.
Assembled everything and can't wait to start her up tomorrow. As soon as I have tested it I will post video's
I have the engine and it runs great. Hard to start the 1st day, but after it runs, I can re start it by hand. has anyone tried running the engine with higher Octane? I'm running regular pump gas 87 and I need to run higher for my other gas engines at the field. will 100 Octane hurt this motor at 25:1 full synthetic Oil?I put this engine on a Hangar Nine 1/4 Scale DeHavilland Tiger Moth. I have had four flights on this plane/engine. I really like the engine. It idles very well and has tons of power. I am using a 20X8 Xoar prop and there is plenty of pull. The idle is fantastic and the sound is awesome. I have not had any issues with it thus far. I did run the engine on the ground for break in using approximately 40:1 mix. I was able to start the engine by hand from the start and have been able to hand start it, although it seems to take a few more flips than I would like. I am inclined to believe that the problem is with my fuel supply setup and not the engine. I am using a two line fuel set up, one for the clunk and one for vent. The fill comes into a "T" that is between the carb and tank. I can see that I am getting some small air bubbles in the line when I am filling the tank, so it stands to reason that air could be getting sucked in to the carb, rather than the fuel. It is a fine engine that runs really well. I have nothing negative to say about this engine.im looking for a biela 4 blade scaleprop for my ngh38cc. What dimensions do u guys recommand? Im considering biela 16*8, 15*9, 14*10 but im not sure wich one will give it the most power rpm ???This engine is a winner for the price. Just received mine and everything looks good. The prop im using is an Xoar 19X8. Running it on ASPEN 2stroke fuel with 2pcnt oil mixture.
Im going to mount the engine in a 60" Pitts Python.Atualmente dos melhores motores Gas a 4T e pelo preo no a melhor
Manual download now [0kb] Manual download now [0kb] No File Name download now [551kb] No File Name download now [100kb] 596414334X435868X17.jpg download now [100kb] No File Name download now [100kb] NGH38 download now [100kb] NGH38 download now [100kb] No File Name download now [551kb] Hawker Hurricane 2m/NGH38 download now [3.19Mb]