Registrieren

Product Finder

Einstellungen

Useful links

Live-Chat
 
[["US","AU","GB","DE"]]
Registrieren
Shipped From:
  • USA
  • Global

SK450 Dead Cat "Defibrillator" Power und A / V-Verteilungsplatine und Power Shield

SK450 Dead Cat "Defibrillator" Power und A / V-Verteilungsplatine u...

QTY:

Now save Speichern 15,29 € 15,29 €

Special Price 8,05 € 8,05 €

You save Speichern 15,29 € 15,29 €

Was  23,34 €

Stock:
Gewicht:
463 g
SKU:
9171000236

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!

Combine

essential items and
acc
Product
Description

Wir zogen den Defibrillator und schockiert einige ernsthafte Leben in die toten Katzen-Konvertierung! Die Spinne Stil Quad-Copter war schon genial mit seiner optimierten Arm Winkel und Layout für einen Propeller frei FPV Ansicht. Und nun das mit Spannung erwartete Progression zu einer integrierten Stromversorgung und A / V-Verteiler und Stecker in Strom abgeschirmt.

Die neue untere Platte hat einen direkten Lötpunkte für den Motor ESC Stromleitungen direkt an der Basis der Arme und Macht "in" Pads direkt über der Batterie befindet Verkabelung zu minimieren. Es gibt Netzanschluss des an der Vorderseite, Rückseite und Mitte für FPV Getriebe und Flugregler, die alle mit dem Leistungsschild gebunden, die mühelos liefern ein geregelt, gefiltert und RF-Rauschen abgeschirmt 5 Volt auf eine satte 3 Ampere für die Kamera und Flugregler und 12 Volt bei 1 Ampere für die hungriest von Videosendern. Die Video-Anschlüsse auf der Vorder- und Rückseite auch nicht nur die Spannung liefern, sondern tragen auch das Audio- und Videosignal von der Front-Kamera auf der Rückseite Videosender montiert. Dieses Upgrade sparen Sie Gewicht, reinigen Sie Ihr Layout und die Zuverlässigkeit zu verbessern durch Verbindungsausfälle zu reduzieren. Ich denke, das tote Katze hat neun Leben, nachdem alle!

Eigenschaften:
• Integrierte Energieverteilung
• Wick Stil Lötpunkte
• Kamera und Videosender integrierte Verkabelung
• 3 oder 4 Zelleneingangs
• SMPS-Wandler mit HF-Rauschschutzschild
• Thermische Protected

Specs:
Eingangsspannung: 8-16V (3-4 Zellen LiPoly)
Gewicht: 142g
Ausgang: 5V / 3A und 12V / 1A

* Anmerkung der toten Katze Defibrillator - Konvertierung für die SK450 den SK450 Rahmen und tote Katze Konvertierung erfordert unten zusammen.

Product
Specifications

Zusätzliche Information

  • Artikelnummer:
    9171000236
  • Brand:
    Nein
  • Gewicht ( g)
    463.00
  • Länge
    375.00
  • Breite:
    30.00
  • Höhe:
    215.00
Community
Discussions
Rate&
Review

Schreiben Sie Ihr eigenes Review

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
I am completely happy with this, what a great product! This did wonders to clean my quad up! Some sort of schematic would have been nice however a quick check with my DVOM and I was off and running! This is a must have for the Deadcat frame!!!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
great thing, saves a lot of cables

and makes it look cleaner
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This is a must for your dead cat upgrade

making the whole upgrade look the bees knees
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Fairly straightforward but I wish it came with documentation on what each connector does.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I was hoping this board would make the addition of a camera and Vtx easy and quick. Not so.

The connectors on the board are male 4 contact connections. It is very difficult to find female 4 contact connectors. I tried using 3 conductor female servo connectors without the outer sleeve. When installed there is not enough room for these connectors on the controller and battery connector and the connector will hit the top board.

The best solution is to remove all of these connectors and install header pins. Once this is done standard male servo connectors can be used. The 4th pin is for audio, which I did not use so the 3 pin connectors would work.

Somewhat disappointed as this created a lot more work than should have been necessary.

If the board would have had header pins. I would give 5 stars.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
this is a great idea, too bad it will be useless if they ban fpv
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
So a friend and I are building dead cats. His is built and flying and after a hard landing the copper band for his ground circuit going to the defibrillator cracked and started pealing off. My frame hasn't been build because my filtered 12v to my video TX is shorted to ground out of the box. .......Not to mention his was nose heavy with a go pro 3 and a 3300mah 3 cell. So I ordered a 4000mah 3 cell because I have a heavier go pro 2 and ccd board cam for fpv but then ran into my electrical short when pinning out the board. I had high hopes for the dead cat but am having second thoughts now for sure.
Cheap lower defibrillator board.
Nose heave with a go pro sized camera. (With 3300mah)
Arms flex

verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I had bigger hopes for this. You have 5V in the front and 12V in the back and a just one extra pin intended for video between front and back. I would like to see both 5V and 12V front and back and some extra pins that I could use for whatever.



The defibrillator seems to output 10V on the 12V pin based on just a quick test with 3S.



Also note that the pins are FEMALE for everything. If they where male we could use the extra servo cables we have...



Connecting a Tarot 2D gimbal to this needs hacking. The defibrillator is in the way and the provided holes are not suitable for the Tarot. I opted to add a separate plate in between the deadcat and gimbal.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Totally agree, the idea is good, like the Black Sheep TBS Discovery product, but the difference is they give you hook-up pins and connectors. HK, at least give us a reference or source to find the pins we need. Come on HK, you have a good concept, follow it through and give your customers a complete product.......after all you require us to buy three different kits to get "one".
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
  • Dead Cat PCB Board

Upload video
Upload
Files