Turnigy 63-64-A 280Kv 65A Brushless Outrunner (52-30)

• Overall
• Quality
• Value

Customer Rated

Dec 23, 2011

There's no stock since november, does anyone know when stock arrive for this motor ? I need 2 motors to build an electric montain board.



see ya

• Overall
• Quality
• Value

Customer Rated

Nov 06, 2011

fly this motor in a 2,4m an-2, with yeti spinn 99 on 8s 4000 turnigy with a 20x10 apc-e, weight complete 9,4kg. later i will try a 4 blade 18" varioprop for a better scale look. im sure you cant get more qualitiy for this money
i m verry happy with this combo, works well without any problems.

paul
www.mac-fly.eu

• Overall
• Quality
• Value

Customer Rated

Jun 01, 2011

Very good engine! I use it for 1,8m CMPro Marathon 24. I have done about 50 flights. I broke a few propellers (bad landings) but engine is still working very well!!! I don't recommend rear mounting (after firewall) - bad vibrations!!! Front mounting (in front of firewall) works very well.

My setup is:

8S5000 mAh 25C Turnigy lipo

100A HV Sentilon Turnigy

18x10 (19x10) TGS Sport propeller

About 1,6-1,8 kW!!!

You can see it at: http://www.youtube.com/user/mariuszmariusz121?gl=PL&hl=pl

• Overall
• Quality
• Value

Customer Rated

Apr 13, 2011

Construction of this motor is very solid. This motor is so nice looking you will want to tuck it in at night! Here is my setup:



Sentillion 100A HV ESC - I really like this ESC (so far) for a few minutes run time and full throttle for a few seconds it barely gets warm.



Turnigy 2200mah 3s 20C batteries - I bought 9 of these. Wired 3 sets of 3 in series. 1 set = 9s 2200mah, 2 sets = 9s2p 4400mah, 3 sets = 9s3p 6600mah. I can mix and match these batteries however I want now. When I am not flying my big plane I can use these batteries in my smaller planes.



Turnigy 5a sbec (8-40v) - You need to buy a separate bec with the Sentillion ESC. This one works great.



TGS Sport 18x8E Precision propeller - I bought a couple of these because they were so cheap. Under $4 a piece. Nice prop.



9s1p - 1800 watts

9s2p - 2050 watts

9s3p - 2350 watts (I figure about 20lbs of thrust)



This setup seems to suit this motor very well. Motor and ESC do not get too warm. This should fly my 1/4 scale super cub very nicely with power to spare!

• Overall
• Quality
• Value

Customer Rated

Apr 03, 2011

Bought one and installed on an Ultimate 90 conversion so far so good on 8s 4000mah with a 20 x 8 APC prop. Measured on a Watts meter it hits WOT @ 64.10 Amps peak and 1842.2 watts peak. The 4 stars is because they dont list the max watts :0( Hope it holds up

• Overall
• Quality
• Value

Customer Rated

Mar 31, 2011

TRES BON MOTEUR RAPPORT QUALITE-PRIX
MONTE SUR UN JODEL GRAUPNER DE 2.20M AVEC 2 X 5S-5000 25C TURNIGY
HELICE GRAUPNER 20X10 ET CONTROLEUR 100A SENTILON, PUISSANCE EXTRA POUR TIRER UN PLANEUR DE 8KG.
CHAUFFE NORMALEMENT QUAND ON TIRE DEDANS.

• Overall
• Quality
• Value

Customer Rated

Dec 14, 2010

Stats with 100 amp Sentillon ESC, 18 x 10 prop and 2 5C 5000 lipos.
At 25 amps, 880 watts, at 60 amps, 1950 watts. More than enough to fly a 1/4 scale, 16 lb Piper Cub like aircraft.

• Overall
• Quality
• Value

Customer Rated

Nov 03, 2010

Nov 1 2010

Amazing motor Turnigy 65-64 one of the best Ive used. Powering a 78" WS Lancair 120 8s 4000Mah nano batt using a 16x10 APC prop

• Overall
• Quality
• Value

Customer Rated

Nov 02, 2010

I use this motor on my Seagull Super Decathlon .120, it pull 5kg with 8s and 17x8 FIALA wood propeller, the plane weight is 6kg.



about 10 minutes of classical aerobatic fly



http://www.rcgroups.com/forums/showthread.php?t=1331818#post16439610

• Overall
• Quality
• Value

Customer Rated

Nov 01, 2010

It would be a 5 star, but my engine come with the "lenght B" out of specs because the bearing was not in the correct place. I had to open the engine and with a proper device, put it in place. After that, the dimension come to normal, and I powered it up. Happy with the product, but dissapointed with quality control. Still recomend the engine.