Turnigy B36-56-04 2600kv Inrunner

• Overall
• Quality
• Value

Customer Rated

Oct 30, 2011

brought one of these a month ago. used it 4times running 4s 5800mah 25c with 120amps sec and 36mm prop in my rc surfer and it got extremely hot and died. motor had plenty of power tho when it was running.

• Overall
• Quality
• Value

Customer Rated

Oct 29, 2011

I just received 2 of these motors, haven't done much testing yet. Just a basic test connecting to ESC (without installing in a model) to make sure it works.

It looks well made; and the noise level isn't very high when it works.

Note that the weight of the motor is 170g (including wires as shown on the picture) and not 260g. Even when wrapped in plastic and packed in cartoon box the weight is 185g.

I noted that it gets warm when runs on full throttle - even only for a few seconds, even without any load, even only on 3S lipo battery

• Overall
• Quality
• Value

Customer Rated

Oct 29, 2011

I just received 2 of these motors, haven't done much testing yet. Just a basic test connecting to ESC (without installing in a model) to make sure it works.

It looks well made; and it the noise level isn't very high when it works.

Note that the weight of the motor is 170g (including wires as shown on the picture) and not 260g. Even when packed in the plastic and cartoon box the weight is 185g.

I noticed it becomes warm after running on full throttle even for a few seconds (even without any load at all) so I guess it will become hot in real use. I plan to use water cooling anyway...

• Overall
• Quality
• Value

Customer Rated

Oct 29, 2011

I just received 2 of these motors, haven't done much testing yet. Just a basic test connecting to ESC (without installing in a model) to make sure it works.

It looks well made; and it the noise level isn't very high when it works.

Note that the weight of the motor is 170g (including wires as shown on the picture) and not 260g. Even when packed in the plastic and cartoon box the weight is 185g.

• Overall
• Quality
• Value

Customer Rated

Oct 12, 2011

This motor is great! Works great in my hobbico superstar EP. Fits the stock brushed mount perfectly!

• Overall
• Quality
• Value

Customer Rated

Sep 26, 2011

I picked one up for a 40 " boat project and it rips flat out on 5s . Huge power with the rite aplication great buy and great motor

• Overall
• Quality
• Value

Customer Rated

Aug 15, 2011

Stopped working after about 10 min in my 1/8 monster truck maybe good for 1/10 scale think I will get a XL size motor this is a large size.

• Overall
• Quality
• Value

Certified Buyer Rated

Jul 16, 2011

runs wicked have got on back of tunnel hull hornet needs a 100amp esc to run ,great value.

• Overall
• Quality
• Value

Certified Buyer Rated

Jun 29, 2011

I have put it in a jet FLYFLY thunderbird with a chensung 90, 5s 4000 and esc 200A HK.Watt'up tell 95A and 1700w !!! edf run to 44.000 rpm and thunderbird 230 km/h.I have put a heatsink.. motor not extremly hot...

• Overall
• Quality
• Value

Certified Buyer Rated

May 26, 2011

I filed the shaft and used it on a 1/10 Short course truck(HPI Blitz). It was way too powerful on 3S plus. Shredded the tires like they were paper, but it sure was fast. Cheap alternative to the VXL... but you need to make sure the shaft is long enough. It's much shorter than most car motors. It also needs to be modded to accept a car pinion.