Lieferant werden Blog Neue Artikel
Registrieren

Gesamtpreis

0,00 €

Warenkorb 0 Warenkorb 0 Loading...

Turnigy Multistar 10 Amp Multi-Rotor Brushless Regler 2-3S

Generating Links

Turnigy Multistar 10 Amp Multi-Rotor Brushless Regler 2-3S

Preis:

Now save speichern 0,00 € 0,00 €

7,25 €
Bereits gekauft Discontinued Product

Please continue searching for a similar product.
SKU:
9351000001
Kostenloser Versand? Klicke hier um mehr zu lernen!

Multistar WSR sind ein Qualitätsdrehzahlregler zu einem fantastischen Preis sind! Für eine einfache Installation und einfache Einrichtung haben diese WSR bewährte hervorragende Leistung zu bieten, wenn sie in Multi-Rotor-Anwendungen eingesetzt. Wenn Ihr Start in Multi-Rotoren und benötigen eine einfache Lösung zu installieren, die getestet und bewiesen mit Multi-Rotor Handwerk zu arbeiten, dann haben diese Drehzahlregler für Sie.

Diese WSA verfügt über einen sehr glatten und linearen Gasannahme, ohne eine schnelle und gestochen scharfe, Reaktion auf jede Drosselklappeneingabe zu opfern. Sicherheit ist nicht bei allen Multistar Esc die mit einstellbaren Batterie LVC (Set Batterietyp LiXX LVC zu deaktivieren) vergessen, blockiertem Motor (Überlastung) Schutz, Signalverlust Abschaltung und sicher Bewaffnung.

Alle Multistar Serie ESC ist gekommen, mit Kugel-Anschlüsse installiert, die auf die ESC Nennleistung Handhabung geeignet sind. Dies ermöglicht eine Plug-and-Play ermöglicht, indem einfach die entsprechende Batterieversorgung Teiler Zugabe (3,4 oder 6 ESC) und Motorleitungsverlängerungen von der Multistar modulare Zubehörprogramm. Was könnte einfacher sein?

Alle Funktion des Multistar ESC ein ATmega MCU, die die Tür zu anpassbaren Firmware öffnet - für diejenigen, so geneigt! oder alternativ eine Programmierkarte kann mit der installierten Software für eine schnelle und einfache Einrichtung mit der Pre-geflasht Software verwendet werden.

Bitte beachten Sie die zugehörige Artikel unten für ein Lot frei Multirotor-Power-Lösung Ihren nächsten Multirotor-Projekt gerecht zu werden.

Eigenschaften:
• Glatte und lineare Drosselklappensteuerung
• Schnelle Reaktion auf Gaseingang
• Atmel MCU
• Stalled Motorschutz
• Drosselklappensignal verlieren Schutz
• Sicheres Einschalten (Gashebelsperre)
• Unterstützung 480Hz + hohe Bildwiederholraten (bis zu 499hz)
• Kompatibel mit Programmierkarte

Specs:
Konstantstrom: 10A
Eingangsspannung: 2-3 Zelle Lipo
BEC: Ja (linear) [entfernen Mitte Draht zu dissable]
BEC Ausgang: 5V / 2A
PWM: 8 KHz
Max RPM: 240,000rpm für 2 - polige Brushless Motor
PCB Größe: 22mm x 17mm
Entladung Stecker: männlich 2mm Rundstecker
Motorstecker: Weiblich 2mm Rundstecker
Gewicht: 16 g

Bedienungsanleitung zum Download verfügbar unter Registerkarte "Dateien".

Video hochladen

Registrieren Sie sich bitte, um Videos hochzuladen anmelden oder Registrieren

Themen
Sortieren nach
Neueste Themen
* Nickname:

* Deine Antwort:


Geben Sie den im Bild gezeigten Text in das Feld unten ein
*Verifizierungs-Schlüssel:
Abbrechen
Senden
Poste ein neues Thema
* Nickname:

* Dein Thema:



Geben Sie den im Bild gezeigten Text in das Feld unten ein
*Verifizierungs-Schlüssel:
Beitragsthema

Registrieren Sie sich bitte, um Bewertungen zu schreiben anmelden oder registrieren

| Verifizierter Käufer

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jul 27, 2014

So tiny and lightweight and perfect! Already ready to go with 2mm connectors on all the wires. At this price its a no brainer.. Perfect for my 250!

Kickingmad | Verifizierter Käufer

  • Overall
  • Quality
  • Value

Customer Rated

Jul 22, 2014

Don't bother with these they don't perform well at all. and can not be flashed with socket tool as atmega chip is to small very small. wast of money get some Simon k instead I'm very disappointed with these want my money back their useless for multi rotors!!!!!!

bill987 | Verifizierter Käufer

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jul 06, 2014

Mis avec turnigy multistar 1704 pas de surchauffe bon vario

ToddJ | Verifizierter Käufer

  • Overall
  • Quality
  • Value

Customer Rated

Jun 09, 2014

Bought these for my 250 mini quad with multistar 1704 motors and mini APM flight controller. I did also got the program card and set them up best i can. Even on NIxx on lowest setting my battery alarm goes off and they are already cutting the power to the motors. I am gonna try the HK f10a flashed with simonk next as these will eventually lead to a bad crash. Also the overload cut off is annoying because if you touch back down one or more motors will quit and you have to disarm and rearm. I am not sure why they engineered these the way they did since basically they are not good for multirotors at all??

JAMES | Verifizierter Käufer

  • Overall
  • Quality
  • Value

Customer Rated

May 15, 2014

Good esc(s) placed in my 330 frame with a KK2.1 board flashed with 1.11 firmware, 3s 1000mah Zippy compact batt, Turnigy 10amp Multistar esc(s) 8ch 9x receiver, power board soldered the esc direct to it and XT60 batt plug on it, 8045 props, this thing it a rocket and getting 6 minutes flight time. After flight everything is cool. Will hoover with only 40pcnt throttle. Motors are Turnigy D2822/17 1100 kv. I did soldered 3.5 bullet ends on everything.

RCBUG80 | Verifizierter Käufer

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Mar 10, 2014

No better than any non flashed esc for multirotors, after flashing with simonk they are 10x better, but this is not easy as there are no pads and the hk flashing tool is too big for the atmega chip on this esc, so you have to solder directly to the chips pin outs. For this reason I would not buy anymore as there are others available that are far easier to flash. If they are specifically for multirotors why does it have brake settings, set to medium as default lol.

They also have no throttle calibration, they are auto like dji escs, but you get throttle calibration when flashed.

adrien | Verifizierter Käufer

  • Overall
  • Quality
  • Value

Customer Rated

Feb 23, 2014

i've got a few brands of 10amps this is the one which fits me the best especially compared to the piece of crap red brick also from here...

Przemyslaw | Verifizierter Käufer

  • Overall
  • Quality
  • Value

Customer Rated

Feb 18, 2014

Really cool ESC for mini quadcopter. I use them with Turnigy Multistar 1704-1900K, kk2.1. And works well. I calibrated them straight kk board.

Evil Pusher | Verifizierter Käufer

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Feb 07, 2014

nice little ESC. Runs without flashing to SimonK also good enough for smaller Multicopter.

NumnutChriS | Verifizierter Käufer

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Feb 06, 2014

Works ok, but gets hot faster than eg. the tgy plush esc. Bought a bunch for a small quad and put another on a bonsai flying wing. Dont forget to get the programming card too!

  1. 1
  2. 2
  3. 3
Kundendateien
Manual - Turnigy Multistar Brushless ESC Download [2384]
Multistar 10A SimonK 1 Download [115]
No File Name Download [94]
Turnigy Multistar ESC Manual Download [2384]
No File Name Download [214]
Multistar 10A flashed with simonk 1 Download [819]
Multistar 10A flashed with simonk 3 Download [3348]
Multistar10A-1 Download [229]
Multistar10A-2 Download [167]
Turnigy ESC All Download [2298]
Datei hochladen

Registrieren Sie sich, um Dateien hochzuladen.
Bitte anmelden oder registrieren um jetzt Hobbyisten zu helfen!