Neue Produkte Forum
Registrieren

Total Price

0,00 €

Warenkorb 0 Warenkorb 0 Loading...

Turnigy Multistar 20A V2 Schlanke BLHeli Multi-Rotor Brushless Regler 2-6S

Turnigy Multistar 20A V2 Schlanke BLHeli Multi-Rotor Brushless Regler 2-6S

Discontinued Product

Please continue searching for a similar product.
SKU:
9351000061-0
WANT FREE SHIPPING? Click here to find out more!

Multistar WSR sind ein Qualitätsdrehzahlregler zu einem fantastischen Preis! Für eine einfache Installation und einfache Einrichtung haben diese WSR bewährte hervorragende Leistung zu bieten, wenn sie in Multi-Rotor-Anwendungen eingesetzt. Wenn Sie beginnen, in Multi-Rotoren und benötigen eine einfache Lösung zu installieren, die getestet und bewiesen mit Multi-Rotor Handwerk zu arbeiten, dann haben diese Drehzahlregler für Sie.

Diese V2 ESC-Funktionen BLHeli Software für einen sehr glatten und linearen Gasannahme, ohne eine schnelle und gestochen scharfe, Reaktion auf jede Drosselklappeneingabe zu opfern.

Alle Multistar Serie ESC ist gekommen, mit Kugel-Anschlüsse installiert, die auf die ESC Nennleistung Handhabung geeignet sind. Dies ermöglicht eine Plug-and-Play ermöglicht, indem einfach die entsprechende Batterieversorgung Teiler Zugabe (3,4 oder 6 ESC) und Motorleitungsverlängerungen von der Multistar modulare Zubehörprogramm. Was könnte einfacher sein?

Alle Multistar WSA-Funktion ein ATmega MCU, die die Tür Firmware anpassbare öffnet - Die V2 Multistar kommt mit BLheli Software vorinstalliert, und für diejenigen, so geneigt, eine einfache USB-Tool verwenden, ist für Konfiguration und Aktualisierung über die BLHeli Suite GUI zur Verfügung.

Bitte beachten Sie die zugehörige Artikel unten für ein Lot frei Multirotor-Power-Lösung Ihren nächsten Multirotor-Projekt gerecht zu werden.

Eigenschaften:
• BLHeli Software
• USB-Tool Aktualisierung und Konfiguration über BLHeli GUI-Software
• Glatte und lineare Drosselklappensteuerung
• Schlankes Design für eine einfache Rahmenmontage
• Schnelle Reaktion auf Gaseingang
• Atmel MCU
• Stalled Motorschutz
• Drosselklappensignal verlieren Schutz
• Sicheres Einschalten (Gashebelsperre)
• Unterstützung 480Hz + hohe Bildwiederholraten (bis zu 499hz)
• Unterstützt OneShot125

Specs:
Konstantstrom: 20A
Eingangsspannung: 2-6 Zelle Lipo
BEC: Ja (linear) [Entfernen Mitte Draht zu deaktivieren]
BEC Ausgang: 5V / 3A
PWM: 8 KHz
Max RPM: 240,000rpm für 2 - polige Brushless Motor
PCB Größe: 62mm x 13mm
Entladung Stecker: männlich 3mm Rundstecker
Motorstecker: Weiblich 3mm Rundstecker
Gewicht: 20,3 g

  • Artikelbezeichnung 9351000061-0
  • Brand MultiStar
  • Kapazität ( mAh) -
  • Gewicht 30.0000
  • Länge 90.00
  • Breite 10.00
  • Höhe 15.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

GREAT DEAL, WORK SUPER WELL AND ARE PERFECT SIZE FOR MY QUADCOPTER ARMS

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

GREAT DEAL, WORK SUPER WELL AND ARE PERFECT SIZE FOR MY QUADCOPTER ARMS

Awesome little ESC. I use them on Flite Test airplanes, they are nice and light and the BEC works awesome. On the long side, but being so light outweighs that.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Awesome little ESC. I use them on Flite Test airplanes, they are nice and light and the BEC works awesome. On the long side, but being so light outweighs that.

I use 4of these in my Hercules quadcopter with 2216 motors and 4s battery, mounted inside the arms.
They work perfectly and stay nearly cold. I will order some more of them for my next project.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I use 4of these in my Hercules quadcopter with 2216 motors and 4s battery, mounted inside the arms.
They work perfectly and stay nearly cold. I will order some more of them for my next project.

I use 4 of them on a quadcopter, conncted through an APM and they work perfectly. However I have 2 more not working on a plane, connected to an Assan 2.4GHz V2 receiver (MPX Tx and Assan universal TxModule). They work using a servo tester but not on the receiver (nothing happens, like there is no signal). The Rx works OK with any other brand of ESC, so it is really a problem with the Multistar ESC.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I use 4 of them on a quadcopter, conncted through an APM and they work perfectly. However I have 2 more not working on a plane, connected to an Assan 2.4GHz V2 receiver (MPX Tx and Assan universal TxModule). They work using a servo tester but not on the receiver (nothing happens, like there is no signal). The Rx works OK with any other brand of ESC, so it is really a problem with the Multistar ESC.

I just bought 4 of these, 3 worked 1 failed. I have purchased many mulitstar esc's and have them on many of my multirotors. Till now I have been very pleased with this brand. I will continue to buy them because of price and performance, but there is a quality issue that needs to be addressed. In failing I mean the motor would not start, it tried for about 2 sec each time I initiated the mulitirotor, so I swapped motors because this was a brand new esc which didn't work so I switched to a plush esc and both motors tried will now work.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I just bought 4 of these, 3 worked 1 failed. I have purchased many mulitstar esc's and have them on many of my multirotors. Till now I have been very pleased with this brand. I will continue to buy them because of price and performance, but there is a quality issue that needs to be addressed. In failing I mean the motor would not start, it tried for about 2 sec each time I initiated the mulitirotor, so I swapped motors because this was a brand new esc which didn't work so I switched to a plush esc and both motors tried will now work.

cute little esc, still not small enough for trifecta tail tray, nonetheless the quality is good and it has bootloader so much easier to change firmware than stock esc which needs soldering or flashing tool.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

cute little esc, still not small enough for trifecta tail tray, nonetheless the quality is good and it has bootloader so much easier to change firmware than stock esc which needs soldering or flashing tool.

no frail ESC, slim built is easy to install between arms.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

no frail ESC, slim built is easy to install between arms.

Ordered these to fit inside 16mm arms (15mm inside), they fit perfectly.
Sadly the quality control is low, I ordered in total 5 Opto's and 3 with the BEC for my Hexa, and found 1 Opto and 1 with BEC to be faulty out the box. Strange issue with on as it was acting differently to the others and the other one just did not work out the box.
I'm not sure if this is relevant, but the two faulty ones I ordered about 3 weeks before the 6 working ones, i wanted to test them but they got stuck in the post so I ordered the 6 I needed. Maybe the new batch is now better?
Anyway, I had 6 working so I'm using them with MultiStar Elite 3508-268kv motors with 17x5.5 props and a 960 Hexa.
Upgraded firmware to BLHeli v14 and altered some settings to get my best results.
Closed Loop MUST be OFF as with Low Voltage Limiter.
Motor Gain at 1, the same with Startup Power.
Temp protection off, PWM Dither 7 and Low RPM Power Protect On.
Demag MUST be OFF.
For best results PWM Frequency / Damped MUST be set to "DAMPED LIGHT"
Motor Timing is best at Medium, Low pulls more power!.
Anything noted as MUST caused the motor to run slower or react to throttle changes strangely or slowly. Others were decided by current draw or best feel.
Any settings not included here either where not available in v14 or seemed unimportant.
Kev

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Ordered these to fit inside 16mm arms (15mm inside), they fit perfectly.
Sadly the quality control is low, I ordered in total 5 Opto's and 3 with the BEC for my Hexa, and found 1 Opto and 1 with BEC to be faulty out the box. Strange issue with on as it was acting differently to the others and the other one just did not work out the box.
I'm not sure if this is relevant, but the two faulty ones I ordered about 3 weeks before the 6 working ones, i wanted to test them but they got stuck in the post so I ordered the 6 I needed. Maybe the new batch is now better?
Anyway, I had 6 working so I'm using them with MultiStar Elite 3508-268kv motors with 17x5.5 props and a 960 Hexa.
Upgraded firmware to BLHeli v14 and altered some settings to get my best results.
Closed Loop MUST be OFF as with Low Voltage Limiter.
Motor Gain at 1, the same with Startup Power.
Temp protection off, PWM Dither 7 and Low RPM Power Protect On.
Demag MUST be OFF.
For best results PWM Frequency / Damped MUST be set to "DAMPED LIGHT"
Motor Timing is best at Medium, Low pulls more power!.
Anything noted as MUST caused the motor to run slower or react to throttle changes strangely or slowly. Others were decided by current draw or best feel.
Any settings not included here either where not available in v14 or seemed unimportant.
Kev

This ESC working good with multistar 2216 motor and 4s battery.
Except one serious issue: here is how to reproduce it
1. connect the battery and wait for 10 min
2. after 10 minutes, your esc should begin to beep, then wait another 3 minutes
3. disconnect and reconnect your battery really fast

Then you have a very high chance to burn both your esc and your motor. I have burn two esc and two motor in the same way.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This ESC working good with multistar 2216 motor and 4s battery.
Except one serious issue: here is how to reproduce it
1. connect the battery and wait for 10 min
2. after 10 minutes, your esc should begin to beep, then wait another 3 minutes
3. disconnect and reconnect your battery really fast

Then you have a very high chance to burn both your esc and your motor. I have burn two esc and two motor in the same way.

great ESC... very small for tube install... configuration -> no problem with BLHeli Tool... flashing software is not necessary to use them... very low heat generation... exactly that i missed...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

great ESC... very small for tube install... configuration -> no problem with BLHeli Tool... flashing software is not necessary to use them... very low heat generation... exactly that i missed...

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save