Entwickelt für Parkflyer 3D zuverlässige und saubere Energie zu liefern. Diese Brushless Outrunner mehr Leistung bieten und mit seiner hohen Effizienz, lange Zeiten laufen.
Ein Qualitätsmotor, gebaut speziell für Flugzeuge entwickelt, um mit einem 250 Watt Brushless Outrunner zu fliegen.Spec.
Batterie: 2 ~ 3 Zelle /7.4~11.1VRPM: 890kvMax Strom: 14ALeerlaufstrom: 8V / 0,7AStrombelastbarkeit: 18A / 15secInterner Widerstand: 0,20 Ohm
Gewicht: 67g (ohne Stecker)
Der Durchmesser der Welle: 4mm
2S ~ 3S Li-Po / 6 ~ 10-Zellen-Ni-MH / Ni-Cd
9x6 ~ 11x3.8 prop
Geeignet für Sport und Maßstab Flugzeuge mit einem Gewicht von 15 bis 30 Unzen (425g-850g).
Gewicht ( g)
Kv (rpm / v)
Max Currents (A)
Leistung ( W):
Länge B (mm):
Kann Länge D (mm)
Max Spannung (V)
Welle A ( mm):
Unit Weight (g):
Durchmesser C (mm)
Gesamtlänge E ( mm)
Widerstand ( mh):
Schreiben Sie Ihr eigenes ReviewGreat quality, Pulls my extra around like it was lighterThat bushing collar, on the back-end, with the set-screws, is the bane of this motor, in my opinion. It interferes with the E-Flight EFLM1915 outrunner stick-mount. I tried to compensate, using Hobby King 10mm stand-offs, but the bushing interferes with these also. Why couldn't the motor's designers have used a snap-ring retainer, on the axle, instead of a bulky bushing???I have ordered more than 40 of these motors, and the initial quality of these were very good. out of 10, 9 ran nice an smooth. Now compared that to my last order in which only 2 out of 10 ran nice and smooth. The remaining 8 had some really bad resonance at certain speed or the motor shaft was actual robbing against the base. In short Hobbyking really need to do something about the build quality of these motors.INCREDIBLE POWER, RELIABLE, I USE ON APLHA 450, GIVE ME LOT OF POWER, USE A 9X4.5 PROP AND GOES INCREDIBLEThis seems to be a fairly high quality motor. It ships with a Xmount and prop adapter. The mount uses two different size screws (supplied) so pay attention. I used 3.5mm bullet connectors.
The plane is a 580g ready to fly scratch built foamy with a semi symmetrical wing, a 1300mAhr 20C 3cell battery, 25A ESC. The prop was 10x4.5 turnigy slow fly prop, product# 9329000026. The motor seemed to develop massive torque spinning the prop with ease. The first flight I landed after 10 minutes of putting around the sky to check everything out. The motor was cool with no problems with mounting or anything else. I swapped the battery with another identical 3 cell and sent her back up, but this time to flog the new motor and plane.
The second flight: Vertical climb was 3/4 throttle, full throttle was a bit too much for the air frame but more than enough to power out of trouble. The motor spun up with authority and had no problems hauling this rigid plane around the sky. I abused the plane and motor for 15 minutes, brought it in for several touch and go landings, heavy on the power back up. I brought it back in at 20 minutes, the ESC hadn't even limited power from the battery!! The motor was slightly warmer but only about 110F.
This is a very efficient motor on my plane with a 10x4.5 prop. I'm considering the purchase of several more. Time will tell quality, but for now I would highly reFantastic motors! Using them on my quad and they haven't given me any problems.Used this to upgrade my hobbyzone super cub to brushless. I absolutely love it. Made the super cub much smoother and more stable. A little faster but mostly helps the plane perform slow loops and hold inverted flight much much better. Very inexpensive way to make your super cub a lot more fun.Excellent motors. Feel very well made. No weird sounding bearings. Just keep in mind that you'll have to make the center hole of the motor mounts of the HK X525 V3 frame bigger to fit the shaft collar. Other than that they're great with 10x4.5 props!here is the prop test data on 3s
Prop Amps thrust-gr
Prop test data 2s
13x8-12.27A-733grSame motor as E-flite Park. Well made and runs great on 3S lipo.
With "heavy duty" 4mm shaft...