Rüsten Sie Ihren 1.20 Größe Verbrenner-Modell mit dem Turnigy RotoMax 1.20 Brushless Läufer-Motor. Dieser Motor liefert saubere und effiziente Energie für Ihren großen Maßstab Flugzeug ohne die Verwirrung und Ärger von Nitro-Kraftstoff.
Wenn es mit einem 8s Lipo-Akku, 19x10 "oder 20x10" Propeller und ein 80Amp ESC die RotoMax Motor kombiniert wird ausdrucksstark, reaktionsschnelle Leistung liefern, die nur eine elektrische Einrichtung zur Verfügung stellen kann.
Dieser Motor ist geeignet für Holz, Kohle und elektrischen Propeller hat die Welle auch eine 4 mm Schraube anzupassen, um Einbau eines Spinners Ihrer Wahl leicht erschlossen.
Batterie: 8 Zellen /29.6V
Max Strom: 65A
Leerlaufstrom: 29.6V / 1,55 A
Innenwiderstand: 0,027 Ohm
Pole - Zähler: 24
Der Durchmesser der Welle: 8mm
Empfohlene ESC: 80A 8S Kompatibel
Empfohlene Prop: 19x10 "oder 20x10" APC
Gewicht ( g)
Kv (rpm / v)
Max Currents (A)
Leistung ( W):
Länge B (mm):
Kann Länge D (mm)
Max Spannung (V)
Welle A ( mm):
Unit Weight (g):
Durchmesser C (mm)
Gesamtlänge E ( mm)
Widerstand ( mh):
Schreiben Sie Ihr eigenes ReviewThis is a great motor. Heaps of power, excellent quality and easy to cool with large diameter. I installed mine in a 1850mm wingspan Sbach300 model with 8S battery pack and K-Force 120A ESC: 9020000002. The ESC works well with the motor using the default programming. The only problem I had is that HK do not seem to have their propeller recommendation correct. I used the recommended APC 19x10" prop and it draws 90A on a 8S battery pack (2 x Turnigy Nanotech 4S 45C)!! That is something like 2700W!! I would hate to think what a 20x10 would draw! I didn't have any smaller propellers so used end point adjustment on my radio to bring maximum throttle down to approx 65pcnt to achieve 2000W at full throttle. Plenty of power for the Sbach for effortless aerobatics. I am not into 3D so cannot comment on 3D performance, but I do have unlimited vertical performance. To me, it is equivalent of a 1.20 glow or 30cc gas engine when setup for 2000W. Clean and punchy electric power, I am a convert!I tried mine with a K-Force (HW) 120A HV esc on 9S and the esc stuttered, then caught fire. It was only pulling 80A, 19x12 apc e prop on 9S 4500''s. Timing was set on 19 degrees and pwm was at 8KHz.HK should ask what esc the manufacturer used, and what were the settings: advance in degrees and PWM in KHz. I have this motor in a Kyoso Corsair and it makes a loud screetching noise past 80pcnt throttle and looses sync. My setup is 18x10 prop on 9S with a YEP 120A HV 14S esc. This setup pulls only 75A. I use soft start and 24 degrees advance with 12KHz frequency. I have tried every other combination from 8kHz all teh way up to 16KHz, with timing advances from 18 degrees to 32 degrees, as well as "auto" timing to no avail. I only found a slight improvement when I switched from "plane slow" to "heli fast" startup. Of course governor is off, low volt cutoff is off, and freewheling is enabled. I suspect the YEP 120 cannot handle this (28 pole) motor, I wonder what ESC the Rotomax 1.2 manufacturer tested and reccomends.Not recommended.
Burned after 3 mins flight, also caused failure of the 80 amp esc.
Where running on 8s and APC 19x10 in a Extra 300.
Thanks god i had external power to radio system, so i could land the model safely.moteur a vraiment de la puissance mes chauffe un peu quand mme.
helice 19/8 8s ESC Castle Creations Phoenix ICE 100A
EDGE 540 5kgHi. I have this motor and I want to use it in a paraglider, but using a normal 100a esc on 6s. I will never go over half throttle as it is only for slow flying. I will be using 20x10 prop. Will this work.? I have noticed a jitter noise when I open throttle. Any help?These motors are strong... With the suggested 190A Turnigy ESC and a 20 X 8 Classic prop from HobbyKing I got 3.78 KG of thrust.
You can even get one on eBay with free swhipping. Just search for ROTOMAX
Mine Rotomax 1.20 is on a 93" L-4 Cub.Here's and update to a few more test we ran yesterday.
We installed this motor on our 2.35 meter Piper L-4. We used a 22.2Volt 45C 4000mAh battery. We tied the tail to a solid bench with 14 gauge wire and a Weigh scale in series with it..
18 X 10 (APC)= 2.23 kg......... 18 X 8 (APC) = 2.68 kg........... 19 X 10 (APC)= 3.24 kg........ 20 X 8 (Classic) =3.78 kg......
Great low cost powerful motor.Received this Motor a while ago to fit into our Green 2.35 Meter Piper L-4 and finally put it on an ESC/battery test setup. I hooked it to a Mystery 200A ESC with BEC. I tried different Battery Voltages and found that @ 11.1V the motor ran well. As the voltage was increased to a 14.8V battery the motor had problems starting to turn and jittered roughly. As the Throttle was increased the motor finally started running. On a 22.2V battery it just sat there jittering horribly and would not start at all. We tried every combination of re-programming that Mystery ESC to no avail...
We then swapped it out for a Hobby King PRODUCT ID: HK-SS200ALV
ESC with an external BEC PRODUCT ID: SBEC-26V.
The motor now runs like a champ turning a 18 X 10E prop. It runs with so much power we ordered a 2nd motor and a yellow 2.31 meter Piper J-3 Cub.
Big motor ..tested with 6s ..planning to put it in a E-Bike