12 Channel Tx/Rx video system with CCD camera.
The camera uses a quality glass lensed SONY CCD camera system & a powerful 1000mW tx.
Unlike other generic systems, we have produced a wiring loom and included it with the camera so that the Tx and camera will be compatible and on the same voltage.
If you buy your camera and Tx seperately the plug polarity and voltages may be very different.
1 x SONY CCD 1/3inch Camera
1 x 2.4GHz 12 channel Video Transmitter (1000mW)
1 x 2.4GHz 12 channel Video Receiver
CCD sensor type:1/3 color SONY CCD
PAL: 500(H)*582(V) (Included)
Scanning system: Interlaced scanning
Horizontal resolution: 420TV line
Minimum Illumination 0.01LUX/F1.2
S/N Ratio: 48dB
Gamma Modification: 0.45
White balance: Auto
Auto backlight compensation: Auto
Input voltage: 9~12.6V
Electric current 80MA
Electronic Shutter: 1/50 (60) ~ 1/100,000s
Video output: 1.0VP-P composite video
Operation Temp.: -20~50
Flight time: Approx 60min/100mah 3S
FPV Tx Spec.
Channel: 12-Ch, AV synchronization
Input voltage: 8~12V
This Video transmitter is amazing!!
I have done hundreds of flights with it an I am VERY happy with it! The video quality is super good an the range is good, too! (little more than 2 kilometers with stock antennas, but much more with good antennas, I have done 6km with CloverLeaf/3-Turn-helical antennas!!) There is only one problem: The Vtx is getting hot! So opened it and filled it completely up with heatsink paste. Do This and make sure that the TX is getting fresh air during flight and you are fine!Completely useless China-quality crap. I waited for it for weeks and found the TX to be totally dead.
Good camera but the Tx gets heated up...As a Radio Ham and aerial designer , ill build an antenna system that will work over 5Km with this system, When I test ill come back and give the results, curruntly achieved 4.65 KM on 5.8 GHz (200mW ) see www.williamsbuild.net
Check the connection of the camera. vcc is inverted to the site of VoutHi Everyone,
I purchased this item and when I connected the cables to make the first test didn't work. The camera got too hot and I start looking around to understand why . Then I noticed that the cable that connects the camera to the battery and TX was incorrectly assembled , so the red was connected to Vout and the white to . After a long battle to get HK attention I had to send the package back to them. So HK decided to send me a replacement which arrived last week. I got it and this time before connecting and switch it on I checked the cable and once more the cable was connected in the wrong way. Not to lose more time I made the modification and the camera works fine now. My point is, if someone is planning to buy this package, pay attention to the cable, this way you may avoid a broken camera and all the costs to send back to HK and get a replacement.good tx and rx, mine gets hot but i readed some reviews and orderd a esc heatsink pack, this in combination with a small pc fan and your off to go!!Hello all ,
1.Delivery was very fast , my advice buy a batteries for the transmitter and to the receiver
Please note this came without any manual book or wring instruction.
But HK make 90pcnt perfect of the wring ..It not complex to make the wring but it will be wisely to buy and plastic adapter .
2. The camera came as in the picture (I built my own cover and adapter to the UAV plane ) but my advice
Don't save the money and buy camera adapter.
3.camera picture is good ! make sure your transmitter is cool up .
It would be good if Hobby King would just sell the TX (transmitter) by its self as they do for the 5.8ghz as I have 4 receivers now but only use 2 of them and will end up with more of them as I have to buy complete systems for my other planes. HINT HINT HKmesafesi olduka yksek,kullandnz kumandada 2,4Ghz olmamal,kumandann sinyali kamera sinyalini bastrabiliyor.