Register

Product Finder

Settings

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Register

5W White LED Alloy Strip 150mm x 12mm (3s Compatible)

5W White LED Alloy Strip 150mm x 12mm (3s Compatible)

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
Weight:
10 g
SKU:
371000065
Product
Description

5W White LED Alloy Strip 150mm x 12mm (3s Compatible)

Specs:
Dimensions: 150 x 12mm
Weight: 8g
Connector: JST
beam angle: 120 degree
Power: 5w
color temperature: 6000-6500 ± 200K                   
Voltage: 11.1v-13.5v (3s Lipoly)               
Current: 300mA            
Luminous flux: 400-450LM            
Color rendering index: 70-85                
Material: aluminum plate                
Service life: 50000 hours                
Operating temperature: -20 - +60 degree Celsius

*Note: please make sure current draw is lower than 300mA or you risk damaging the LED strip
Product
Specifications

Additional Information

  • SKU:
    371000065
  • Brand:
    No
  • Capacity (mAh)
    No
  • Shipping Weight(g)
    10.00
  • Length:
    155.00
  • Width:
    5.00
  • Height
    45.00
Community
Discussions
Rate&
Review

Write Your Own Review

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
I have to agree with the other reviewers on this LED strip. It claims it's 3S compatible, but it gets EXTREMELY hot when connected to a fully charged 3S pack. A resistor is necessary to run this with 3S.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I run them with a Meanwell LDD-300L (http://www.meanwell.com/mw_search/ldd-l/LDD-L-SPEC.PDF) switching DC current driver to ensure the leds are driven within rating despite the battery voltage (you can run them from about 10V to 36V input voltage). They are very bright, but only heat up to about 40C. Additionally, this driver has a PWM input (up to 1Khz, not servo-PWM) which I have connected to a GPIO of my Pixhawk flight controller using a N-FET inverter (the GPIO can't drive the current neccessary for the PWM input, I've used 100 Ohm in series to the gate for protection, 100K pull down on the gate and 1K pull up to the battery voltage on the drain). Using the PX4-built-in application gpio_led, the led stripes begin to blink when the battery reaches a low voltage. The PWM input can just left unconnected if not needed.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
They get very hot. Run at 9.0VDC and make sure of polarity. Some of the JST's are improperly assembled
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This LED has been tested by me on my plane and have to say that in clear weather the LED was visible even at a distance of / - 350 m.
Led is on the leading edge of the wing glued with glue 302 HK.
as power supply is a 3s lipo and use a 10-ohm resistor-10watt.
Will in the future several models of these LEDs provide.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Do NOT connect it to fully charged 3S directly!
Never!
Only 2S
(or LiFePo4 half charged)

Good product!

It should work as a LED - via resistor or LED driver.

Vdrop:
8.40V * 200mA
8.69V * 300mA
8.95V * 400mA
9.07V * 450mA
9.22V * 500mA
Put resistor in series R=(Vbat - Vdrop)/I (choose current you want) Resistor 1-3W (P=(Vbat - Vdrop) * I )

Don't know how long it survive if get wet or in a cold weather.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Tested with 11.1V 3S lipo. Very bright although theres a need to keep the current to 300mA to prevent overheating.
*It is so bright it blinds ur eyes.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
tres lumineux, bien visible l'exterieur en pleine journee, chauffe assez fort, contrairement a ce qui est annonce le courant consomme est de 1,1 A sous 12V, ce qui fait plus de 12W, plein d'applications possibles...
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Customer files
No File Name download now [1805kb]

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.