Register

Product Finder

Settings

Useful links

 
[["US","AU","GB","DE"]]
Register
Shipped From:
  • Global

7.2V 4.5A UBEC 2-5S Lipoly (6-23v)

7.2V 4.5A UBEC 2-5S Lipoly (6-23v)

Now save save $0.00 $0.00

$8.65
Out of stock!
Rating:
Stock:
OUT OF STOCK
Weight:
20 g
SKU:
72V45AUBEC

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!

Product
Description

This Small and lightweight UBEC features a High efficiency switch mode design providing better heat dissipation when compared to linear voltage regulators. The shielded PCB design and output EMF coil makes helps provide a stable and low noise voltage output. This UBEC also features built-in reverse polarity protection.

Specs:
Input: 6V-23V (2-5S Lipoly, 2-6S Li-Fe or 5-15S NiXX Battery Pack)  
Output: 7.2V/4.5A (Less than 50mV peak to peak voltage @ 2A)
Dimension: 47mm x 11mm x 25mm(LxWxH)
Weight: 11.4g (wires included)

Product
Specifications

Additional Information

  • SKU:
    72V45AUBEC
  • Brand:
    N/A
  • Weight(g)
    20.00
  • Length
    97.00
  • Width:
    9.00
  • Height:
    75.00
Community
Discussions
Rate&
Review

Write Your Own Review

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Gets hot without load!
7.2v is correct, but 4.5a is a waaaay no!
1.5-2a max. Used a protek 130t servo on a hobbywing 150a sec. It got a 6v 3a build in esc. The servo works fine. Now connect the same servo to this bec, that its suppose to be 7.2v and 4.5a, but it glithes like crazy.
Please dont put 4.5a on the label when it cant even deliver 3a.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Almost a year previous version worked in my DEX408 with "epoxy waterproof".
2nd season with the same BEC =) It's great!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Bought this one to use for a 50 dollar Savx servo. Worked fine on 2s, but on 3s output voltage rised to 8.4V an efficiently burning the servo. I do not recommend this one to anyone.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
It does what it should do.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Howdy, I used to get these when they looked differently, with a single capacitor, and the board was narrower. I ordered one of these since it had the same specs and installed it into my 450 Pro, and had a crash. It turned out that after a relatively short period of time, like 3:30, the unit glitched out and locked up (lost power), causing the AIL servo to pull down with subsequent total loss of control. Naturally, the heli rolled left and went in fairly hard.

I was able to reproduce this on the bench by powering up the unit and exercising the controls just like one would in flight, and at 4:24 the exact same thing that must've occurred in flight happened: the AIL servo pulled down and the unit locked up (or went dead) with no control after that. About 3 seconds later the iKon reinitialized.

I may try another, but I would recommend that everybody bench test these first!@@

Cheers,

Bill
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
xxxxxxxxxxxxxxxxxxxxx
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very good UBEC! Use this on an Quadcopter to take the 4s Lipo down to 7.2Volt for the FPV transmitter. Very light and also small.

Nice!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I have a bunch of the Turnigy 3amp(5amp max) UBEC's and I love them. They run cool and provide great power. But I bought a bunch of 7.2 volt servos and really wanted to use this. It gets really warm, almost hot just being connected to the battery. And this was without the servos plugged into the receiver yet. I wanted to like it and I still need a good 7.2v UBEC. Maybe Turnigy will come out with one or I will have to go with with a Castle Creations.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
tres bon ubec pour mon servo qui fonctionne en 7,2v et aussi compatible avec mon recepteur orange gr300 specktrum qui encaisse le 7,2 v (ce n'est pas le cas de tout les recepteurs )
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I get it last week, and I tested this UBEC and i love it.



Vout rate 7.25 - 7.26 with low ripple.



I use it for my Turnigy servo.



:)
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.