The popular Naze32 is here! Initially designed for use with small to mid-sized multirotor craft, it has become the go-to controller for a host of Multirotor projects and propheads.
The infamous Hamasaki AKA “timecop” was not happy with the limitations and performance an 8-bit MCU could deliver on current FC platforms, so he set out to make a flight controller that could take just about any demands a developer could throw at it, and thus was born the Naze32. At the heart of the Naze32 is a 32bit ST micro work horse of a processer, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration.
The Naze32 comes as the most complete Acro Version yet, with both strait and 90deg pins for your preference and a matched break out harness.
The HobbyKing version is fully authorized and royalties are paid to the developer on each Naze32 sold.
• Flexible motor outputs, support various airframe types:
Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
• Up to 8 ch RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spektrum satellite receivers.
• Built in FrSky telemetry inverter (shared w/main port)
• Battery voltage monitoring
• Modern 32-bit processor running at 3.3V/72MHz (STM32F103CB).
• Onboard MicroUSB for setup and configuration
• LEDs so bright, they could blind you
• MultiWii-based configuration software for easy setup
• rev5 hardware
36x36 mm (30.5mm Mounting)
5.3 grams (no headers, 7.3 grams with)
2000 degrees/second 3-axis MEMS gyro + accelerometer (MPU6050)
Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line
2x5 pin header
12x2 pin header - straight header option (break it into 4 2x3 for motors/telemetry pins) OR
3x6 right angle header and 2x3 right angle header - right angle option
1x RC breakout cable
Download User's Manual for rev5
Configuration software - Chrome Baseflight Configurator (preferred)
Can also use 2.3 or newer version of MultiWiiConf (Java-based) from http://code.google.com/p/multiwii/downloads/list.
Software is open-source! Code repository at
- Blade Count:
Great older board, good price.
Great fc, used it on my epipdb by quad otters enzo, definitely recommend this board.
Great flight controller.
Works just fine, great price and easy to program. Very happy with this FC, no problems so far, I run Cleanflight on it with pwm, but no problems, works as expected!
This boards are really great if you are looking for tidy wiring and direct onnections. Be prepared to be able to solder though.
Great Flight Controler!
I had a cc3d atom before, i flashed both of them to cleanflight and flew them in the same copter, so i could compare them. At first I noticed, that the naze32 semms to work a lot faster! It connects much faster to my cleanflight software than my cc3d did before. I haven`t flown it for that long, but until know I could really recomend it! There had just been a little issue with setting it up, because my channel 1 was not the channel 1 in cleanflight and so on with the other channels, but I had that issue with my cc3d before too, so Iam not sure if it?s not cleanflight?s fault.
All in all pretty nice product.
eine der besten fc am Markt gnstig und gut
Epic control board. I previously have had two kk2 boards and haven't been happy with them and had to get refund from hobby king twice and had great customer service. I then bought this board having seen that flite test uses this board. Has great control and better programming than kk2. For me it was very easy to use after watching flite test's setup videos stuff. The auto level isn't yet setup perfectly but the manual mode is good enough and very stable. Well worth buying and a great little fight control board.
great FC for acro, you only need to short the boot-pin to flash your favourite firmware
Very good flight controller! I use it for a 210 mini quad, it is much, much better, more precise than the KK2 board, I had before. It is also very cheap for the value. I use it with cleanflight, and I think it is perfect! My only downside is the USB connector is on the back, not on the side, so it's not so easily accessible, but that's all.
Love this nice board on my x525 quad... I use it with CleanFlight added a simple NMEA ttl GPS on 57600 and 5Hz for FPV OSD only (not for GPS based flight modes) bought at banggood. This version is simple without Baro or Magnetometer, but for learning and enjoying FPV flying with some soft 3D moves it is a great choise. This board is revision 5, but good as much as version 6... see or feel no difference in flight at all.
CLI Variables download now [63kb] Naze Basic download now [566kb] Naze32 manual download now [341kb] Graupner HoTT Telemetrie 2 download now [359kb] Graupner HoTT Telemetrie 3 download now [2191kb] Graupner HoTT Telemetrie 1 download now [534kb] No File Name download now [590kb] Thanks HK download now [3737kb] Updating download now [724kb] Updating parts download now [12kb] No File Name download now [1366kb]