This combo contain:
Quanum Chaotic 3D Quad (P&P) *1
Turnigy TGY-i10 10ch 2.4GHz Digital Proportional RC System with Telemetry (Mode 2) *1
Turnigy Graphene 2200mAh 4S 45C Lipo Pack w/XT60*1
Chaotic 8045 3D Props (Carbon Reinforced Nylon) *1
Quanum Chaotic 3D Quad (P&P)
This is Chaotic. What a way to go with this extreme 3D flying quad. There is no telling what you can do with this quad from slow stable (well semi stable) flight to buzzing around upside down for 3D flying with flips and rolls thrown in just for fun of it.
It comes with all the great gear for flying out of the box. Just add the transmitter and receiver of your choice. The Chaotic is completely fitted out with the Quanum Madcow flight controller driving 2212-1300kv motors, Afro 30A ESC’s and big Gemfan 3D 8” propellers. Electronics are covered in a vibrant polycarbonate shell for extra protection and easy orientation.
The Madcow flight controller comes preset with three flight modes.
Veal mode: (Stabilized mode) 0 – 100% of the throttle range corresponds to normal motor rotation only. In this mode the multi-rotor will maintain level balance automatically while roll and pitch are centered. The multi-rotor will not flip and roll and the angel of tilt is limited.
Grilling mode: (Acro Stabilized mode) 0% - 100% of the throttle range corresponds to normal motor rotation only. In this mode the multi-rotor will maintain level balance automatically while roll and pitch are centered. The multi-rotor will still flip and roll and the angle of tilt is not limited. This is often called “horizon” or “ratititude” mode but is not capable of inverted flight.
Madcow mode: (3D stabilized mode) 0% - 50% of the throttle range corresponds to reversed motor rotation, 50% - 100% range of the throttle corresponds to normal rotation. In this mode the multi-rotor will maintain level balance automatically while roll and pitch are centered. This is often called “horizon” or “ratittude” mode but with added reversing of motors for inverted flight.
3D flying - the Chaotic way to fly.
• Tough and light weight carbon fiber frame
• Large 400mm wheelbase
• Quanum Madcow flight controller for 3D flying
• Bi-directional 8” 3D carbon reinforced propellers
• Three stabilization modes – Veal (Stabilized), Grilling (Acro), Madcow (3D)
Weight: 613g (without battery)
Motor: 2212 1300KV (DJI slot style shaft)
ESC: Afro ESC 30 Amp (SimonK firmware)
Flight Controller: Quanum Madcow 3D
Propellers: Gemfan Bi-directional 8in 3D Carbon Reinforced Propeller set CW/CCW Multirotor (DJI slot style)
Power distribution board: HobbyKing mini PDB with XT60 Connector
1 x Quanum Chaotic 3D Quad P&P
1 x Manual
1 x Sticker set
1 x Velcro Tape
2 x Gemfan Bidirectional 8” Propellers (CW)
2 x Gemfan Bidirectional 8” Propellers (CCW)
1 x Battery 4S 1800~2200mAh LiPoly pack
1 x 5~6CH Transmitter and receiver
Turnigy TGY-i10 10ch 2.4GHz Digital Proportional RC System with Telemetry (Mode 2)
The TGY-i10 uses 2.4GHz AFHDS 2 (automatic frequency hopping digital system 2) which spans the whole frequency band. Equipped with a high sensitivity receiver, this radio system guarantees an optimal and highly secure link between the transmitter and receiver.
The innovative design of the new TGY-i10 makes the handset extremely lightweight while the menu items and data is presented on its 3.55 inch TFT touch screen!
The TGY-i10 radio system uses high gain, high quality multi directional antennas, each transmitter has a unique ID, when binding, the receiver saves that unique ID and will only accept signals from the transmitter it is matched with, this prevents interference from any other radios and ensures the safety of your model.
The TGY-i10 radio system utilizes extremely efficient components and high speed processor chips for those complicated mixing settings. In comparison this radio system uses 1/10th of the power of a standard FM system.
Another key feature of the TGY-i10 is its telemetry capabilities, the radio system has the ability to monitor real time rpm / voltage and temperature data which provides added security when flying your models.
If you require more than 10 channels an i-Bus receiver (TGY-AEV01) is included, which will provide you with an extra 4 channels which allows an additional 16 servos to be connected.
The TGY-i10 really is one of the most intelligent and innovative radio systems available today and all at a price that will not break the bank!
• 2.4 GHz AFHDS 2 (automatic frequency hopping digital system)
• Compatible with all TGY AFHDS receivers
• Real time telemetry monitors signal strength, Rx voltage, flight pack voltage, RPM and temperature
• Audio and visual warnings when limits are exceeded
• 3.55 inch, 240 by 400 pixels (WQVGA) colour, high contrast TFT-LCD touch screen
• Power on/off safety feature
• 3 way switch x 2, 2 way switch x 5, momentary switch x 1 and slider control switch x 2
• Easy access pop up / down VR controllers x 3
• High-precision double ball bearing gimbal and ergonomic design
• Double antenna structure for improved signal transmission
• 20 model memory including memory expansion slot
• Free software upgrades available online
Transmitter Functions Include:
General functions: Flight conditions, linear / curve mixing, functions / channel / throttle delays, channel mixing, logic switches, Aircraft type, RX setup, dual rates / expo, endpoint adjustment, channel offset, trim / subtrim, throttle down / curve / delay / reverse, system menu, model name, timers etc.
Airplane / Glider functions: Aileron / flap / spoiler, elevator to flap, butterfly, V-tail, dual elevator etc.
Helicopter functions: Throttle hold / mix / curve, pitch curve, swashplate mixing / type / ring, governor, gyroscope etc.
Model Type: Helicopter / airplane / glider
RF Range: 2.4055-2.475GHz
RF Power: Less than 20 dBm
2.4G system: AFHDS2A
Code type: GFSK
Low Voltage Warning: Yes (less than 3.75V)
DSC port: Yes (USB, HID)
Memory Expansion: SD card
Antenna Length: 26mmx2
Weight: 620 grams (with battery)
Battery Capacity: 3.7V (1700mAh)
Dimension: 195 x 189 x 43mm
(TGY-iA10) 10 Channel 2.4GHz receiver
(TGY-BA1700) Li-ion battery 1700mah
(TGY-ATM01) Thermometer sensor
(TGY-AVT01) Voltage sensor (optical module)
(TGY-APD02) RPM sensor
(TGY-AEV01) I-bus receiverMicro USB cable
User Manual (CD)
Version: TGY-i10 19-3-2015
This update fixes some bugs and adds refinements to the programming. It also improves the overall stability of the system.
Turnigy Graphene 2200mAh 4S 45C Lipo Pack w/XT60
TURNIGY, the name synonymous with performance, reliability and innovation is excited to release a powerful new battery chemistry in the Turnigy Graphene!
What does this really mean for you? Well not only do Graphene batteries go harder for longer but they're unlike anything you have seen or used before.
Turnigy Graphene packs utilize carbon in the battery structure to form a single layer of graphene just 0.335nm thick, making that type of battery substrate the thinnest known to mankind. The graphene particles form a highly dense compound allowing electrons to flow with less resistance compared to traditional Lipoly battery technologies.
The result is a battery capable of maintaining greater power output whilst remaining much cooler under load. Since heat and resistance are the natural enemy of batteries Graphene chemistry has significantly reduced these problems and the result is an incredible boost in cycle life.
Turnigy Graphene batteries are the new standard for serious hobbyists who require POWER ON DEMAND.
Voltage: 4S1P / 4 Cell / 14.8V
Discharge: 45C Constant / 90C Burst
Weight: 273g (including wire, plug & case)
Balance Plug: JST-XH
Discharge Plug: XT-60
Chaotic 8045 3D Props (Carbon Reinforced Nylon)
Size: 8045 (8x4.5)
Hub: 5mm stepped hub
Material: Carbon reinforced Nylon