-
Product
Description -
Corona CS238MG Metal Gear Servo 4.6kg / 0.14sec / 22g
Specs:
Model: CS238MG
Operating Voltage: 4.8V / 6.0V
Operating Current: 300mA / 400mA
Operating Speed: 0.15sec.60º/ 0.14sec.60º
Stall Torque: 4kg.cm / 4.6kg.cm
Size: 29X13X30mm
Weight: 22g
Dead Band: ≤5uSec
Operating Travel: 40º/one side pulse traveling 400us
Potentiometer: 3 slider/Direct Drive
Ball bearing: MR106
Gear Material: Metal
Gear Type: Digital
Motor: Brushless
Connector wire: 215mm
Operating Temperature Range: -20c ~ +60c
Spline count: 25 -
Product
Specifications -
Additional Information
-
SKU:
CS238MG
-
Brand:
Corona
-
Shipping Weight(g)
45.00
-
Length
76.00
-
Width:
32.00
-
Height:
51.00
-
Speed (Sec/60deg)
0.14
-
Torque(kg)(min. 0.01kg)
22.00
-
Unit Weight (g):
22
-
A(mm):
35.00
-
B(mm)
30.00
-
C(mm)
31.00
-
D(mm):
13.00
-
E(mm):
41.00
-
F(mm)
19.00
-
SKU:
-
Community
Discussions -
-
Rate&
Review -
Got 3 of them, good, very strong, ball bearing and metal gear, good center return. One of mine works good but makes a “grinding” noise. Unassembled, seems ok, but the noise did not stop. Will use it on the tow hook, to reduce risks of failure. Other 2 work good. Very nice the orizontal mount. If you buy this, grab 1 extra.Great little servo. Running one of these for both ailerons on my combat planes (3). Stands up to a lot of rough treatment. Excellent value.Really happy with these for the price. They are strong, quick, and seem precise. I'm using 4 of these in a Sundowner 36 pylon racer, and they have been great so far. They fit perfectly (just slightly fat for the wings, but they fit with some sanding). Precision and resolution are important for a pylon racer where control throws are small, and I've had no problems with these. The plane flies perfectly straight every time the controls are released, and resolution seems good even at small throws. I haven't put on enough flights to judge reliability, but the first several flights have been fantastic. I would definitely buy these again for that "grey area" between a 9g servo and a full size servo.I,ve bought 4 units and I can tell all of them fit very well with arms, no tolerance between gear and arm.Fast shipping, good qualityI have a bunch of these servos and have yet to have one not work perfectly. I have snapped a number of servo arms in combat though and can't find replacements. any of you know what type of servo arm the CS238MG takes? If replacements are available I give this 5 stars. If not, I will no longer purchase Corona servos.I have a bunch of these servos and have yet to have one not work perfectly. I have snapped a number of servo arms in combat though and can't find replacements. any of you know what type of servo arm the CS238MG takes? If replacements are available I give this 5 stars. If not, I will no longer purchase Corona servos.I have old serwo SC238MG with the red inscription Corona. It has well-fitting T-bar lift well. New with the orange inscription are loose. This is not the problem, some tape and it is well. New serwa work so as old, well. ( I always unscrew the casing and check the solder).Smooth, not too noisy, centre OK. The horns, while not being a tight fit on the output shaft are OK once the screw is installed and tightened.Upon testing, the Y2 output transistors are burning out. Why is this? This is very bad.
Upon testing, the Y2 output transistors are burning out. Why is this? This is very bad.Upon testing, the Y2 output transistors are burning out. Why is this? This is very bad.Upon testing, the Y2 output transistors are burning out. Why is this? This is very bad.Upon testing, the Y2 output transistors are burning out. Why is this? This is very bad.Upon testing, the Y2 output transistors are burning out. Why is this? This is very bad.Upon testing, the Y2 output transistors are burning out. Why is this? This is very bad.Upon testing, the Y2 output transistors are burning out. Why is this? This is very bad.Upon testing, the Y2 output transistors are burning out. Why is this? This is very bad. -
Upload
Videos -
Upload
Files -
Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!
Customer filesHow to fix the poor fit of the horns download now [596kb] Servo_corona_fix.pdf download now [630.54Kb]
Sign in
Register
Sign in / Register
OR
or
Register
-
-
-
ACCESSORIES
- EDF Systems & Parts
- Wheels/Landing Gear/Retracts
- Spinner/Adapters
- Propellers
- Wires & Connectors
- Heat Shrink / Shrink Tube
- Flight Stabilization Systems
- Horn/Hinge/Clevis
- Screws, Bolts, Nuts and Fasteners
- Covering Film
- Decal Sheets
- Glues, Lubricants & Tape
- Night Flying Accessories
- Push Rods
- Tube, Rod, Carbon Fiber & Glass Fiber
- Pilots
-
-
-
TELEMETRY & FPV
-
-
-
-
-
POWER SYSTEMS
-
-
-
-
BOAT ACCESSORIES
-
-
-
POWER SYSTEMS
-
-
-
-
POWER SYSTEMS
-
-
-
-
DIY & ELECTRICAL ACCESSORIES
-
-
-
FPV, AERIAL VIDEO & TELEMETRY
-
-
Show Filters
All Categories
Product Finder
Settings
Useful links
-
-
-
ACCESSORIES
- EDF Systems & Parts
- Wheels/Landing Gear/Retracts
- Spinner/Adapters
- Propellers
- Wires & Connectors
- Heat Shrink / Shrink Tube
- Flight Stabilization Systems
- Horn/Hinge/Clevis
- Screws, Bolts, Nuts and Fasteners
- Covering Film
- Decal Sheets
- Glues, Lubricants & Tape
- Night Flying Accessories
- Push Rods
- Tube, Rod, Carbon Fiber & Glass Fiber
- Pilots
-
-
-
TELEMETRY & FPV
-
-
-
-
-
POWER SYSTEMS
-
-
-
-
BOAT ACCESSORIES
-
-
-
POWER SYSTEMS
-
-
-
-
POWER SYSTEMS
-
-
-
-
DIY & ELECTRICAL ACCESSORIES
-
-
-
FPV, AERIAL VIDEO & TELEMETRY
-
-
Cart is empty Make it look better :)
Total $0.00 0 item(s)
Product Finder
-
Lipo -
Motor -
Servo -
Propeller
Most relevant matches are shown. Click Search for more items
