Total Price


Cart 0 Cart 0 Loading...

Dr Mad Thrust 40A ESC for EDF

Generating Links

Dr Mad Thrust 40A ESC for EDF

Already Purchased Discontinued Product

Please continue searching for a similar product.
want FREE shipping? Click here to find out more!

The Dr. is back in his lab bringing you new speed controllers optimized for use with EDF's. These ESC's offer smooth start up and a linear throttle response. No miss starts, or other hiccups. These EDF friendly speed controllers offer a range of programming options programmed through your transmitter or with the optional programming card. In addition to being great for EDF use, these ESC's work well in a variety of fixed wing aircraft and have a governor mode for use in helicopters. 

All Dr. Mad Thrust ESC's feature heavy duty wire leads made from high quality silicone wire and have an appropriately matched battery connector pre-installed. Additionally, the wire leads are extra long since most EDF models tend to have the fan at the back of the plane with the battery up in the nose. The smaller Dr. Mad Thrust ESC's have internal BEC's to save weight, while the larger units are optically isolated, which helps protect your expensive radio equipment. The "opto" units require a separate BEC to power your radio system.

• Optimized for use with EDF jets
• Three start modes, normal/soft/super soft for a variety of applications
• Low voltage cut-off, over-heat protection, and throttle signal loss protection
• Smooth, linear and precise throttle response.
• Program Card can be purchased separately for easily programming
• Throttle range can be calibrated for linear response on all transmitters
• Separate voltage regulator IC for BEC output
• Heavy duty battery leads and battery connector matched to the current capability of the ESC
• Extra long battery leads

Input Voltage: 2~6S (7.4~22.2V) LiPoly
Continuous Output current: 40A
Instantaneous current (10 seconds): 55A
UBEC Output: 5V@3A
Size: 72x31x16mm
Weight: 55g
Battery Wires: 14AWG
Battery Connector: XT60
Motor Connectors: 3.5mm Bullet

  • Dr Mad Thrust HV EDF ESC
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

JanComputerman | Verified Buyer

  • Quality
  • Value
  • Overall

Customer Rated

Mar 05, 2015

I got this ESC along with the recommended Dr Mad 50mm EDF and Dr Mad programming card and it screems on a 3 cell lipo pack drawing about 260 watts and generating a pound of thrust measured while hold it on a digital bathroom scale and pointing it downwards ... yeah this is a screemer. Operating it with a Feather Hitec receiver and servo tester works great after I did the throttle calibration ... power up with full throttle then wait for the beeps then zero throttle and more beeps and you are set to go! Without the throttle calibration it will just beep at you!!

park aviator | Verified Buyer

  • Quality
  • Value
  • Overall

Customer Rated

Aug 08, 2014

Recived mine today cant get it to work think I got a dud power up and all it does is 3 beeps and nothing may have to return

siskojuice | Verified Buyer

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Jun 01, 2014

Great Dr Mad product,ezy esc to program and is compatible with turnigy programming card also comes with all plugs and connectors pre installed and programing sheet very well assembled great value for money.

ruflasto | Verified Buyer

  • Quality
  • Value
  • Overall

Customer Rated

May 09, 2014

Just picked up this d,mad thurst esc with built in bec.And i have to say it is very good tested it on a 4 cell 2200 35c lipo with a 4800kv 64mm edf.pulling 38amps @wot for 20 sec timing set on high,Esc just loop warm and very smooth throtle responce.And these Esc can be programed with the turnigy card so the best deal all round. I will be getting a lot more if thay stay in stock.well worth the money Thanks H K.

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!