FrSky FLD-02 Telemetry Display Screen
Compatibility: FrSky DFT, DJT and DHT
1) Show all connected sensors data;
2) Capable of programming alarm thresholds and directions;
3) Firmware upgradable.
Connect FrSky FLD-02 to the UART and power connection on FrSky telemetry module (Rxd, Txd, +5V, GND) by the provided cable. Confirm the orientation is correct and make sure both switches on the telemetry module are OFF.
Blade: Blade Number
Volt ratio: A1 & A2 Voltage Division Ratio
Unit Set: Speed (m/s or MPH)
Temperature (Celsius or Fahrenheit)
Alarm Set: A1_1/2, A2_1/2, RSSI_1/2
Note: Make sure the battery voltage division ratios are programmed in accordance with those of connected battery voltage sensors.
The alarm thresholds and directions (either above or below threshold) can be programmed. After alarm thresholds and directions are programmed, click “OK”. ”√” means these values have been remembered by the module.
A1 & A2 Voltage
Temperature 1 & 2
Rx RSSI & Tx RSSI
Voltage for each cell
Note: Screen-3 shows up only when FrSky Lipo Voltage Sensor (FLVS-01) is connected, otherwise Screen-4 will show up after Screen-2.
Longitude & Latitude
*Note: Please see "Files" tab for user manual.
Perfect addition to your Frsky enabled module. I am using mine on my turnigy 9x with the DJT frsky module. The supplied cable made it easy to install but just needed some slight pruning with a set of pliers. I have done an unboxing video:
I would highly recommend this product but just be aware that you need a telemetry enabled receiver and at least a voltage sensor to see anything on this display. The V8fr-II that comes in the DJT Module combo is not telemetry compatible; try the D8R-II plus
Probably wont use this screen as I eventually chose the FPV OSD route to telemetry. Great little screen though. Check out RC Model Reviews, works great. Make sure you get the telemetry type receiver and the required sensors etc. FRSKY website not very informative so made a few wrong hardware choices.Nice lcd for your frsky telemetryI love this little screen. I use it with my DJT and modded Turnigy 9X. Plug-n-PlayNice small display to connect to FrSky Tx module (DJT). Not compatible with XJT, shame. Upgradeable. Shows sensor values send from Rx.Hi all!Hi! Could You help me. My friend got new FLD-02 with new x8r and it doesn't show TX RSSI Level on first screen (only rx rssi)! Is that means that tx or rx is broken? Thanks and best regards, Roman.Kein Lieferung mglich zu Deutschlandmuch better then modify my 9xrExcelente, te da la informacin necesaria de telemetra frsky, adems es muy ligero se fija facilmente tan solo con velcro.I am Using it with my 9xr transmiter with frsky DJT module. I am onlyn interested in RSSI. Very nice product.
manual espaÃ±ol download now [164kb] Robbe FC-16 w FLD-02 (1) download now [1700kb] Robbe FC-16 w FLD-02 (2) download now [1530kb] Robbe FC-16 w FLD-02 (3) download now [1819kb] User Manual download now [114kb] Graupner_MX12_with_DHT8_and_FLD02 download now [2457kb] instruction manual download now [114kb] instruction manual download now [114kb] short manual download now [160kb] divider ratio for alarms download now [9kb] Fitted to dx8 antenna 1 download now [2040kb] dx8 antenna rear download now [2040kb] antenna rear download now [1311kb] Manual EspaÃ±ol download now [171kb] Manual EspaÃ±ol download now [171kb] Manual_EspaÃ±ol download now [171kb] Manual EspaÃ±ol download now [171kb] good manual (english) download now [160kb]