These superb little shockie motors offer great performance and great value for money. Hand wound and balanced these super light weight motors are fantastic for the lightest of light indoor 3D profile and F3P models. Equipped with 2mm gold plated bullet plugs and a super light Carbon fiber motor mounts these motors are ready to bolt in and take off!
Light weight design.
Strong and light CF motor mount.
Pre-installed 2mm gold connectors.
Built in prop saver.
Idle Current: 1.5A
Max current: 10.9A
Suggested prop: 9x5
Shaft size: 3mm
Weight: 19.6g (True weight including wires and connectors)
Mount dimensions: 35mm x 35mm
3 x 2mm Female connector
2 x Prop saver bands
1 x CF Motor mount
3 x Pre-cut shrink tubes
Unit Weight (g)
Max Currents (A):
Length B (mm):
Can Length D(mm)
Total Length E(mm):
I intended to use this with a e-flite nieuport. connected to zippy 800mah 2s 20c and a plush 10a esc. Startup up was jerky and abrubt. Tried a HK red brick 10a still same problem. Same with HK 8/10amp. Replaced motor with turnigy park flyer 250 of 2200kv. Big difference. Nice and silky smooth with plenty of power with all three of my tested esc's. Although it looks pretty and appears well made I still can't recommend this red HK motor.Super moteur tres bien conditionn avec les accessoiresTried a 8x4 gws on 3 cell .....15 amps and hot motor. Had to go down to a 6x 3 prop on 3 cell and it would rip the little prop had to really stay on the throttle. Finally tried a 8x4 on a 2 cell and good performance I think it was at 10 amps. Next time out I will try a 9x4.7 on the 2 cell and see what I get. I would buy another one for a crack yak or 7 oz or less airframe with the 8x4 prop. It would be super on a 6oz plane.Very compact and lightweight. I used this motor in a pusher configuration powered by a Turnigy 3S 800mAh 35-45C battery through a Turnigy Plush 12Amp ESC, spinning an orange GWS 8x4.3 prop.
It has great responsive power! But don't expect the motor to last if you don't manage your throttle usage appropriately.
In hindsight, I may have been able to avoid burning up two of these already by evaluating my setup with a watt meter first.Using this in my 3d profile scratch build. Great little motor and very strong built.It took me a while to figure out the slowfly APC prop is the best. The GWS 8x4 was my first choice, but the hub on the motor is too small. I had to use the busing that came with the 8x4.7 slow fly apc prop and then after insertion, drill it out. Now the hub sits on the motor very well and with a tight O-ring, the balance is amazing. The trust is great and the motor flys warm on 2S as I 3D fly a 290 gram biplane from TechOne. I don't recommend any prop larger than the 8x4.7 as it will heat up the motor instantly. Super light and powerful, just be sure you get a tight prop fitting.Good Motor ...........................................................................................................................................Gewicht 19,27g inkl. Kabel(5cm)und 2mm Goldkontaktstecker
Prop-mitnehmer etwas lockerer Sitz fuer GWS (zB.7x6)
28 Statoren - besonders ruhiger Lauf, sehr hochwertige, sehr leichte Ausfuehrung ideal fuer 150-200g SchockflyerJust got one, very well machined, weight is true, relatively clean windings.
Didn't measure thrust yet but feels good!
I plan to use it with a techone spirit, keep you updated...