Country
United States
 
Shipped From:

HKPilot Mega 10s Power Module With XT60 Connectors

HKPilot Mega 10s Power Module Wi...

The HKPilot HV Power Module incorporates both a way to power your HKPilot and accessories as well as report battery voltage and current back to the HKPilot for logging and telemetry data. This can be viewed in the HKPilot’s stored logs or li...
387000052-0

Now save save $0.00 $0.00

$21.28
OUT OF STOCK
30g
387000052-0

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!

Overview

The HKPilot HV Power Module incorporates both a way to power your HKPilot and accessories as well as report battery voltage and current back to the HKPilot for logging and telemetry data. This can be viewed in the HKPilot’s stored logs or live with a telemetry radio connection. All thru a single and tightly included 6-pin cable that directly matches the HKPilot’s/APM/PX4 connector. The on-board switching regulator outputs 5.3V at a maximum of 2.25A, and can be used up to 45Volts (10S LiPo) and at a maximum of 90 amps. The Power Module is ready to use with XT60 connectors pre-fitted, and shrink wrapped for protection.

Note: The Power Module is rated at 2.25 Amps to power the HKPilot, receiver and peripherals (GPS and Telemetry radio) ONLY. To power servos use an ESC with an adequate BEC or a standalone BEC plugged into the output bus, and remove jumper 1 to isolate the two power lines.

Specifications:
Max input voltage: 45V
Max current sensing:90A
Switching regulator outputs: 5.3V at 2.25A max
Connector: 6-pos Molex cable plugs directly to HKPilot/APM/PX4 'PM' connector
Voltage and current measurement configured for: 5V ADC

Includes:
DF13 6 Position Connector 150mm long
HKPilot Power Module with XT60 Connectors

*Note: The reference to APM refers to the ArduPilot project, a family of open source autopilots based on the Arduino open source computing platform, developed by 3DR and the open source community. It consists of a choice of ArduPilot Mega (APM) electronics and a range of free software versions for different vehicles and is governed by an open source creative commons license.

*Note: This is not an original Arduino brand product.

Specs

Additional Information

  • Blade Count:
    N/A
  • Diameter X(Inch):
    No
  • SKU
    387000052-0
  • Brand
    No
  • Watt Hour:
    0.00
  • Weight(g):
    30.00
  • Length
    90.00
  • Width
    20.00
  • Height:
    50.00
Discussion
Reviews

Write Your Own Review

Only registered users can write reviews. Please, log in or register

The connector going to the Pixhawk is the wrong connector (minor pin differences that prevent the connector from going into the board; the side rails and back tabs). There might be a way to shave it down, I tried, but finally pulled the connector off of an old 3DR Power Module and replaced the one on this Power Module. The wire crimped ends are the same for both so it only took a few minutes.

I haven't tried it yet at 9S, but assume that it works if I don't update this post.
I purchaed 2 for my 2 quads and they are well built. Measures voltage and current accurately on HKpilot Mini.
Very well constructed. Only niggle is the thinner wires as they seem fragile. I used heat shrink to stiffen the lead up covering partially the little connectors as well. Powered my HKpilot Mega with no issues! Remember to remove the jumper on the FC if using this! Doesn't heat up and seems efficient! Worth it's purchase!
better quality than previous stuff from hk. all soldered well
Works, but the connector comes loose easily
very good, work well, very easy to use, you are worth a try. the price is very affordable. i use to my APM . thanks
Video
  • HK Pilot Mega Accessories

Upload video
File

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.