Become a Supplier Blog New Items
Language
ENG
USD
Selected Country:
[["US","AU","GB","DE"]]
    Register

    Total Price

    $0.00

    Cart 0 Cart 0 Loading...
    Display : All categories 0 Aircraft 1922 Drones 676 Flight Controllers & Accessories 61

    HKPilot Mega 10s Power Module With XT60 Connectors

    HKPilot Mega 10s Power Module With XT60 Connectors

    You will earn 18 bonus points for buying this item.

    Generating Links

    HKPilot Mega 10s Power Module With XT60 Connectors

    7 Reviews
    Price:

    Now save save $0.00 $0.00

    $22.57
    Already Purchased Discontinued Product

    Please continue searching for a similar product.
    SKU:
    387000052-0
    Discontinued Product
    Please continue searching for a similar product.
    want FREE shipping? Click here to find out more!
    Report Issue Not Cheapest?

    Copy and Share the Below URL

    Product Description

    The HKPilot HV Power Module incorporates both a way to power your HKPilot and accessories as well as report battery voltage and current back to the HKPilot for logging and telemetry data. This can be viewed in the HKPilot’s stored logs or live with a telemetry radio connection. All thru a single and tightly included 6-pin cable that directly matches the HKPilot’s/APM/PX4 connector. The on-board switching regulator outputs 5.3V at a maximum of 2.25A, and can be used up to 45Volts (10S LiPo) and at a maximum of 90 amps. The Power Module is ready to use with XT60 connectors pre-fitted, and shrink wrapped for protection.

    Note: The Power Module is rated at 2.25 Amps to power the HKPilot, receiver and peripherals (GPS and Telemetry radio) ONLY. To power servos use an ESC with an adequate BEC or a standalone BEC plugged into the output bus, and remove jumper 1 to isolate the two power lines.

    Specifications:
    Max input voltage: 45V
    Max current sensing:90A
    Switching regulator outputs: 5.3V at 2.25A max
    Connector: 6-pos Molex cable plugs directly to HKPilot/APM/PX4 'PM' connector
    Voltage and current measurement configured for: 5V ADC

    Includes:
    DF13 6 Position Connector 150mm long
    HKPilot Power Module with XT60 Connectors

    *Note: The reference to APM refers to the ArduPilot project, a family of open source autopilots based on the Arduino open source computing platform, developed by 3DR and the open source community. It consists of a choice of ArduPilot Mega (APM) electronics and a range of free software versions for different vehicles and is governed by an open source creative commons license.

    *Note: This is not an original Arduino brand product.

    Product Specifications
    Videos
    • HK Pilot Mega Accessories
    Upload video

    Only registered users can upload video. Please, log in or register

    Discuss 0
    Topics
    Sort by
    Most Recent Topics
    * Nickname:

    * Your Reply:


    Please, enter the text shown in the image into the field below
    CAPTCHA Image
    *Verification Code:
    Cancel
    Submit
    Post a new Topic
    * Nickname:

    * Your Topic:



    Please, enter the text shown in the image into the field below
    CAPTCHA Image
    *Verification Code:
    Post Topic
    Reviews

    Only registered users can write reviews. Please, sign in or sign up

    GlassKnees | Verified Buyer

    • Overall
    • Quality
    • Value

    Seems To Work Fine

    Apr 21, 2019

    I bought this while building another Tarot 650 Ironman - the previous one crashed during its 2nd test flight when the controller suffered a brownout. I was using 6S power with an APM module that was rated for 6S. This time around I decided to try this one, but I'm waiting delivery of a 6S lipo so I won't know for sure until I test under a full 6S charge, but so far it seems to work using a 4S lipo.

    Walter F | Verified Buyer

    • Overall
    • Quality
    • Value

    Customer Rated

    Jun 30, 2016

    The connector going to the Pixhawk is the wrong connector (minor pin differences that prevent the connector from going into the board; the side rails and back tabs). There might be a way to shave it down, I tried, but finally pulled the connector off of an old 3DR Power Module and replaced the one on this Power Module. The wire crimped ends are the same for both so it only took a few minutes.

    I haven't tried it yet at 9S, but assume that it works if I don't update this post.

    | Verified Buyer

    • Overall
    • Quality
    • Value

    Certified Buyer Rated

    Mar 15, 2016

    I purchaed 2 for my 2 quads and they are well built. Measures voltage and current accurately on HKpilot Mini.

    | Verified Buyer

    • Overall
    • Quality
    • Value

    Certified Buyer Rated

    Mar 08, 2015

    Very well constructed. Only niggle is the thinner wires as they seem fragile. I used heat shrink to stiffen the lead up covering partially the little connectors as well. Powered my HKpilot Mega with no issues! Remember to remove the jumper on the FC if using this! Doesn't heat up and seems efficient! Worth it's purchase!

    | Verified Buyer

    • Overall
    • Quality
    • Value

    Certified Buyer Rated

    Mar 04, 2015

    better quality than previous stuff from hk. all soldered well

    | Verified Buyer

    • Overall
    • Quality
    • Value

    Certified Buyer Rated

    Mar 02, 2015

    Works, but the connector comes loose easily

    | Verified Buyer

    • Overall
    • Quality
    • Value

    Certified Buyer Rated

    Feb 21, 2015

    very good, work well, very easy to use, you are worth a try. the price is very affordable. i use to my APM . thanks

    Manuals/Files
    Customer files
    387000052-0-56855.doc Download [400]
    Upload your file

    Only registered users can upload files.
    Please log in or register to start helping your fellow hobbyists today!

    Need Help
    Live chat

    © 2024 HobbyKing. All Rights Reserved.